So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Linda, great questions! I have only had my rub n buffed hinges in use for a few weeks so far so I can’t say much for long term use yet. I can say that I haven’t had a problem with it rubbing off, but I did have to be really careful hanging my cabinet doors because I noticed that it did rub off on the white paint if I wasn’t careful. (The few spots where that happened, I just touched up the white paint.) I also didn’t have a problem getting it to shine – but I was going for a brushed nickel look which isn’t super shiny. I don’t know that you could get it shiny enough to be a chrome looking finish. Overall I have been really happy with it but I will be sure to share an update after more time passes.
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less. The most common pull sizes for standard cabinetry are 3”, 4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches. Standard knob sizes are less than 1.5 inches in diameter.
Knobs, handles and hinges may seem like insignificant details, but they can have a major impact on your decor. Give your cabinets a quick facelift by replacing outdated hardware. Stylish hardware can give older cabinets a new look while providing the finishing touch on new cabinets. Choose the perfect hardware for your decor by considering a few important elements.
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....
The quick answer is yes, you can change the hinges. The hard part is what type. Cabinet doors have lots of different configurations.....full overlay, partial overlay, inset, etc., etc. The hinges have to fit the door style. There are hidden hinges that screw to the cabinet framework without major holes, and there are European type hinges that require a large hole to set the hinge into. Go to big box and look at the hinges, what is available can be mind boggling, until you understand the type of door you have.
Diane, this is so exciting! I can relate as I had a makeover much like yours ( from 70’s brown cabinets to white painted, but pulls are also painted….black.) that was 5 years ago and we are now in the process of making over a back bedroom into a walk-in closet and part of a bathroom/vanity area. I feel as though I should have taken pictures of the progress and posted blogs! I cannot wait for the finished product. I KNOW you must be feeling the same way about the beautiful kitchen you are creating…
Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
Some styles of kitchen cabinets are designed to open at the side of the door, so they don’t have outer knobs. When re-facing cupboard doors as part of a remodeling project, new knobs can still be added to these self-opening styles. Consider adding knobs or handles that create visual interest. Careful planning is needed as holes will need to be drilled in the cabinet doors to add the new knobs.