We also painted our kitchen cabinets white, and I love the crispness of white cabinets. We used latex paint since we ended up doing most of the work while I was pregnant/nursing a newborn and I didn’t want to deal with the oil-based chemicals and odors. It’s definitely not ideal–the hard, oil-based finish is much more practical for kitchens and cabinets. I’m not a perfectionist so it doesn’t bother me (too much!), but I would definitely recommend taking the time to do oil like you did–yours should last forever 🙂
Installing new Knobs and Pulls are a super easy way to update your kitchen cabinets without spending a fortune. Our kitchen cabinets didn’t even have knobs and pulls installed so I was happy to finally add new hardware. If you’re looking for an easy update for your kitchen by getting new kitchen hardware, you will like my favorite new go-to place for hardware, D. Lawless Hardware.
You may also have seen cabinets that are so modern and minimalist that they have no knobs or pulls whatsoever—and they look like they’re impossible to open! The trick is, in fact, a mechanism with a spring located on the inside of the cabinet. When you push on the corner of a cabinet, you compress and then release the spring, which in turn pops the cabinet open. In order to close the cabinet, you simply push it closed until you hear the little "click" that means the spring is back in its locked position.
Prevent cabinet doors from slamming shut with integrated Prevent cabinet doors from slamming shut with integrated soft-close technology from Everbilt. Designed for a full overlay these hinges are retro fit able and allow any level DIYer to do away with the heavy slamming of cabinet doors. The complete overlay leaves your cabinets with a sleek modern look.  More + Product Details Close
Mid-century modern design grew in popularity from the 1940s to the 1970s. During this time period, there was increased interest in nuclear physics, molecular chemistry, and science fiction which inspired the unique shapes seen in everything from furniture and lighting to homes and office buildings. Mid-century modern style combines vintage elements with sleek and timeless … Continued

Finally, one of the more technical parts of cabinet hardware are the ball-bearing slides or tracks and latches that are used to open and close drawers and cabinets. Sliding tracks are what allow drawers to open and close smoothly, and using drawer slides that have soft-close ball bearings allow them to close slowly so that they don’t make much noise or rattle everything inside. Drawer slides are available in side-mount, center-mount, and undermount versions, depending on the amount of space you have between the drawer and the cabinet opening. 
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
Ceramic knobs bring such charm to your kitchen. They’re reminiscent of a sweet country cottage, or an old world farm house. It’s not hard to imagine the scent of a freshly baked pie or loaf of bread cooling in the window. Ceramic knobs pair quite nicely with natural wood finishes and glass hutch cabinets. Wether you choose plain white or a funky pattern, ceramic knobs give your kitchen a homey flair.
Apparently I would use MP(?) kind of boards (I forget what the man at HD called it) and it costs about $25 for an 8x4 sheet. I would just measure my cupboard doors, then go in and tell them the measurements, and they would do all the cutting. Then I would just prime the boards, then paint them, then pre-drill the holes for the new hinges, then put them up.
Want sleek form? Want functionality at its finest? Say hello to handles. Handles for white cabinets allow a firm and full grip to easily pull open or push close any cabinet door. Handles come in a cornucopia of shapes and sizes to male for a match with your kitchen style. Handles offer installation flexibility, with vertical and horizontal options, which allows for additional detailing for your white cabinets.
Budget is, of course, a key factor in any part of your kitchen remodeling decisions. While you’ll want to pay as little as possible right now, remember that quality matters in the long run. Your local kitchen cabinet showrooms will offer you the largest variety, with people who can help you choose high-quality hardware within your budget. Remember that the price is based on the finish, as well as the design and size. Knobs are less expensive than pulls.
It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.

Kitchens are often thought of as the heart of a household. We spend a lot of time in our kitchens every day, and they’re usually the backdrop of most social gatherings in our homes. If your kitchen style is beginning to feel outdated and uninspiring, there are a number of quick and easy ways to update your kitchen that will save you the time and expense of a complete kitchen remodel.
From round and oval to square and rectangle, cabinet knobs come in all types of shapes and sizes. Show off your personal flair for design with novelty cabinet knobs. If you’re going for a coastal look, we have novelty cabinet knobs shaped like sea shells, starfish and sea horses. If you have a child who plays sports, we’ve got you covered with soccer, baseball and basketball shaped cabinet knobs. We also carry antique cabinet knobs for history lovers.
Kitchen cabinet knobs can really change the look of your cabinets. The best knobs and handles not only suit the cabinet style, but also add to the theme or mood of your kitchen. For example, the warm appeal of hammered copper cupboard handles blends well with rustic kitchens, while the cool sparkle of crystal knobs looks elegant against dark wood cabinets.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
“We find it refreshing for people to purchase what they like and what feels good to them, not caring what the ‘Joneses’ have,” says Renee. The Brandino Brass team regularly works with professionals who have their own signature styles. “One architect in town may use the same small knob all over the house all in the same finish for continuity. Another one will use different styles and finishes in each individual room,” says Jessie Isom, Brandino Brass team member. “There is no right or wrong if you like it.”
The choice between cabinet pulls and knobs isn’t easy — both come with positives and negatives. Keep in mind that you’ll be using your knobs or pulls every day. Whatever you choose should feel natural in your hand and flow with the décor of the room. You should consider your kitchen’s décor and style, the look you want to achieve, your budget, ease of cleaning, ease of use, the weight of your drawers and more.
I had already chosen polished nickel hardware (which I will share more about soon), so my hinges needed to coordinate.  I decided to use Rub n Buff to give them a much-needed update.  If you don’t know, Rub n Buff is a fantastic metallic paste used to give almost anything a metal finish.  I chose it because it is so easy to use and gives a lasting finish.

Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five.  I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.


Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.

We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....

Caring for decorative hardware purchased from Cliffside Industries is easy. Use only a soft cloth dampened with water for cleaning. The most important thing to remember is never to apply any chemicals or abrasive cleaners, including all kinds of soap or detergent. Using these products damages the protective lacquer and may change the appearance of the piece. Any use of chemicals, abrasives or soaps will void your warranty.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.

There are a couple of ways to go about choosing the right color and finish. One school of thought advises you to choose based on the color and finish of the kitchen’s faucet. Given that most faucets are either silver or brass in color, this advice can be limiting, especially if you have your eye on stone knobs or another finish that is not common in faucet design.


If you decide to install these hinges throughout, you’ll also get the privilege of a handy fine-tune adjustment feature, the BLUMOTION function can be turned on / off with an activation switch so you can accommodate different weights of doors. But the soft-close feature doesn’t have variable adjustments like some of the other soft-close hinge systems. Once the soft-close is turned of you’ll be left with a standard self-close hinge.

Interior Door knobs and levers can range from less than $20 to $200.  You can find cabinet knobs and pulls from less than $2 each to more than $20 each.     Solid knobs and pulls are better quality than hollow hardware.  Although you generally get what you pay for with hardware, if your budget is tighter, you might want to choose less expensive cabinet hardware since it’s relatively easy for homeowners to trade it out for better quality hardware in the future.
Traditional style cabinetry typically has elaborate detailing, embellishments and moldings. Decorative, ornate hardware is in keeping with this style. Often, interior designers choose drop handles for traditional style doors with coordinating knobs on the drawers. Want a vintage look? Try a handle with a porcelain overlay for a sophisticated farmhouse feel. 

I have a solid oak kitchen from the late 1980s. I would like to update the cabinets by painting them but my hinges are exposed. Is it possible to change any exposed hinge to a hidden hinge, or are there some styles that won't be replaceable? Also, has anyone else painted kitchen cabinets with exposed hinges in such a way that it looks good? Thanks!
​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.
It's easy to overlook cabinet handles when you're remodeling your kitchen or building a new home. After all, they're fairly small, easy to install and don't cost as much as, say, a refrigerator or new cabinets. Nevertheless, cabinet handles, also called cabinet pulls, and their near kin, cabinet knobs, can make a big difference in the look and utility of your kitchen. You use your cabinet hardware dozens of times a day, and while hardware like cabinet hinges are not highly visible, kitchen cabinet handles are high profile and can add to or detract from the look of your kitchen, depending on how carefully you choose your kitchen cabinet knobs and handles. Keep reading for information on how to choose cabinet handles that will help give your kitchen the look you want.

Ceramic knobs bring such charm to your kitchen. They’re reminiscent of a sweet country cottage, or an old world farm house. It’s not hard to imagine the scent of a freshly baked pie or loaf of bread cooling in the window. Ceramic knobs pair quite nicely with natural wood finishes and glass hutch cabinets. Wether you choose plain white or a funky pattern, ceramic knobs give your kitchen a homey flair.
Installing new hinges can be easy, but only when choosing the correct cabinet hinge upgrade. The door style, door thickness, and hinge type, all play a role. Once this information is obtained, you should be able to find a soft-close hinge that is a direct retrofit to the existing hinge, or choose one of the many independent dampers and keep your current hinges.

You might think that after making dozens of tough decisions during your kitchen remodel, something like choosing handles for your cabinets would be easy. Yeah, so not the case. You’ll soon find out that there are more cabinet knob options than there are stars in the sky. But don’t panic. And by all means, don’t make a knee-jerk decision just to get it over with. When I used to make up design and swatch boards, I would remind clients that the hardware matters as much as the big stuff. Remember, you’ll be looking at and touching your kitchen cabinet knobs every single day. So you want to make the right choice. And after all, this is a micro design element that can have macro impact.

Thank you so much for helping me understand more about the process to choose new kitchen cabinet hardware. We have been really into rustic looking kitchens lately, and I think that some antique decorative nails could really change the way it looks. Just as you mentioned, you can always change the look of your kitchen again if you do not like the way it looks after a couple of years. Thanks for posting!


Wine Logic wine racks are built-in right underneath your kitchen cabinets, eliminating the need to take up any counter space with a freestanding wine rack. Wine Logic racks come with two to five separate slide out trays that each hold up to six bottles of wine. And the best part is, Wine Logic’s horizontal design stores wine in the best possible condition, keeping the corks wet and the wine untouched by air.
I love your site and your super helpful advice. We’re installing full overlay cabinets in our kitchen and we’re trying to select hinges for the upper cabinets — particularly the cupboard doors on the end which when closed is perpendicular to a wall. Since the door aren’t inset, I’m concerned we won’t be able to open the cupboard a full 90 degrees. Basically, the issue is how to solve the problem of the door swing? Are there any hinges that could solve this problem? I can send elevations if that helps. Thanks so much in advance!
“People come in and say they have a ‘standard’ door,” says Renee Genereux of the Brandino Brass team. “But there is no such thing as standard. You need to know your door thickness, how does it swing, what’s the width, what kind of holes do you have.” Avoid multiple visits to the hardware store because you don’t have all of the information and measurements you need. “We give them all of the questions to answer and then they come back with all of it.” Call Brandino Brass ahead of time to ask what you need to know for your visit or check out the sheet below as handy guideline for getting to know your doors and cabinets better.
Below and above the sink can be two different color schemes. Don’t worry, you can mix and match more than you might think and still obey the laws of symmetry. It can provide a sunny, uplifting splash to have a lighter color above the level of the countertops, such as a warm brass or gold. Particularly with items like faucets and sconces, a lighter color around eye level will create a happy glow.
Updating the hardware on your kitchen windows can take them from standard to standout in seconds! Typically, window sash locks and lift pulls blend in with your window color, but switching these traditional styles up with an elegant bronze or a satin nickel finish will add interest and pizzazz to your windows. You can also choose a finish that matches the rest of your kitchen hardware for a pulled together style.
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
“When it comes to hardware, it’s hard to shop on the internet,” says Eric. “Some things that look really good online, look cheap in person and vice versa. Some cheap-looking online items look exquisite in person.” The Brandino Brass team says that not only the look, but the feel of door hardware and cabinet hardware is very important. “You don’t want a handle to poke you or have an awkward grip for your hands,” says Renee.
Shake a can of rust-inhibiting metal spray primer for the amount of time recommended by the manufacturer. Position the can the recommended distance away from the hinges -- it varies among manufacturers. Spray a light coat of primer on the hinges and screw heads using steady, even sweeps. Make sure you spray the sides and edges. Shake the can frequently while you spray. Allow the primer to dry for the amount of time recommended by the manufacturer. Apply a second coat of primer and allow it to dry completely.
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.

If you’re looking for a style that’s hot right now, look no further than modern cabinet hardware. This look features sleek, straight handles in horizontal lines, usually in a stainless steel or chrome finish. The hardware is skinny and will likely stand out against the color of your cabinetry. Another option is a rounded, long and vertical handle in the same finish.
Choose hardware that will contrast with your cabinets. Accent dark wood with brass, stainless steel, chrome or nickel. Light-colored cabinets provide the perfect background for bronze, enamel or copper with an antique finish. Metal hardware with a satin or highly polished finish can be adapted to a contemporary or traditional decor. Oil-rubbed bronze suggests a more casual style. Consider enamel and glass hardware for a Victorian home. Glass is also available in sleek designs to accent a contemporary setting.
Your kitchen is looking beautiful. White paint is a miracle worker…so are you. I have an old 1970’s GE oven that looks just like yours. It’s a great oven and still works perfectly. I had the door, which was originally light brown, re-enameled years ago when I painted my kitchen white. It’s held up beautifully. I just wish I had two ovens like yours. Sure would come in handy for holiday cooking.
×