The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.

I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.

There are a couple of ways to go about choosing the right color and finish. One school of thought advises you to choose based on the color and finish of the kitchen’s faucet. Given that most faucets are either silver or brass in color, this advice can be limiting, especially if you have your eye on stone knobs or another finish that is not common in faucet design.
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less.   The most common pull sizes for standard cabinetry are 3”,  4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches.  Standard knob sizes are less than 1.5 inches in diameter.
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.
It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.

Knikki Grantham is a Trend Manager with over 20 years in the Furniture and in the Furniture and Design Industry. She grew up in the furniture industry with early memories of sawdust and hand tied springs. After working in various phases of furniture production and development she moved into Design Sales for a Luxury high-end retailer, attaining an Associate ASID as well as other accreditations from various furniture manufacturers.
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Kitchen knobs, pulls, and hinges have come a long way from the traditional styles that have been available over the years. No longer are homeowners limited to plain, simple, and functional. Instead, functional and pretty can now go hand in hand. Today’s styles include finishes in antique copper, iron, nickel, polished chrome, aged bronze, polished brass, glass, stainless steel, and antique brass. Additionally, a variety of knobs, handles, and pulls are available in ceramic styles.
Installing new hinges can be easy, but only when choosing the correct cabinet hinge upgrade. The door style, door thickness, and hinge type, all play a role. Once this information is obtained, you should be able to find a soft-close hinge that is a direct retrofit to the existing hinge, or choose one of the many independent dampers and keep your current hinges.
Under-cabinet lighting serves not only a fashionable purpose by creating visual depth in your kitchen, but it serves a functional purpose as well. The added lighting will make everything from chopping veggies to reading recipes to measuring ingredients easier to see as your countertops will be under direct light from above. And as far as style goes, the right lighting can make all the difference!

Once you’ve selected your new handles and pulls, it’s time to remove all the old ones. Using a drill or screwdriver, slowly back the screws out, then gently pull the old hardware away from the door or drawer front, so as not to damage the finish. Keep the old screws and pulls/knobs together in a plastic baggy so it’s easy to donate or toss them depending on their condition. If you’re going to repaint your cabinet doors, do it now.
My go-to shop for all of my hardware needs is D.Lawless Hardware – I’ve been using hardware from there for a while now and it’s always the best quality at the lowest prices. They sell so many other awesome products too. Everything from knobs and pulls, drawer slides and systems, to wood appliques, trim, DIY, craft supplies, outlet covers, and so much more! 
What color will your appliances be? What about your lighting? Your faucet? For some people, matching hardware to appliances may not be particularly important—we’ve seen plenty of kitchens with brass pulls and stainless appliances. But if you like everything to coordinate, consider the whole kitchen when you pick the color of your pulls. (If your appliances are stainless and you don’t particularly like the look of silver pulls, black hardware makes for a harmonious look that isn’t too matchy-matchy).
The next step was to decide whether to go with pulls, knobs, or a combination of the two– and also the size. THIS WILL SEND YOU TO THE MADHOUSE if you’re not careful. To make my decision easier, I perused my kitchen ideas board on Pinterest and realized the look I was going for was modern and symmetrical– and many of the modern kitchen used only pulls, not knobs. Hmmmm, this was interesting. Maybe it wasn’t so hard to choose?

Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.
Use the same guidelines for or your interior doors. If you like the idea of statement door knobs and hinges, go for lots of contrast— dark door knobs and hinges on light doors, for example.  As an aside, interior door levers, which you simply have to push down, are easier for aging hands to operate as compared to door knobs, which you have to twist.

Pick a color scheme and stick with it. This tip is twofold, as it helps tremendously in narrowing down your choices while simultaneously expanding your options. Pick a large swath — say, the entire lower half of the kitchen — and commit to a color scheme. If the drawers in your kitchen are white, and all the hardware shares the same type of finish, the presence of different types of knobs and handles will be a pleasant sight, rather than a distraction.
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.
Aside from polishing, the look of stone hardware is largely in the hands of nature. Though your hardware pieces may all share traits if they come from the same slab of rock, each piece is going to be different. This creates a natural variety in appearance that will add zest to your room. Stone is cool to the touch and looks especially lovely in homes with a woodsy touch.
Personal preference is very important when deciding whether you want a knob or pull. Your hardware should be in keeping with the style of your kitchen, but it must be comfortable to use, too. Carefully check out the knobs or pulls you are thinking of buying. Place them against cabinetry, then see how they fit your hand. Are they the right size and shape for you?
Cliffside is one company that works exclusively with high-quality producers who make sturdy, kiln-fired glass. This glass comes in many different colors to suit your palette, as well as different shapes and sizes. Because the glass is strong, it can stand up to the rigors of dropped kitchen items, quick yanks and more. This durability also means it can be used for more than just knobs — there are glass handles available as well.
​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.

When it comes to designing a kitchen inevitably you have to pick out hardware, and these seemingly small details can literally keep you up at night, going back and forth between brass knobs or stainless steel bars. But thankfully, we’re here to help you get a “handle” on the process. Here are the factors you should consider when choosing kitchen cabinet hardware.
×