We were delighted with the professional quality of Meridian’s services. Your team was always responsive and courteous and went out of their way to ensure that our needs were met. Meridian worked closely with our architect to anticipate issues and deal with them in a timely manner. Our home was built in record time and we are very happy with the quality of workmanship.
I am taking on more and more cabinet refresh projects (for hire), and still never tire of the transformations.  My latest project is an oak, galley style kitchen, and I’m digging deeper into ideas to make these older kitchens look more modern.  Paint is obviously a big hitter in terms of updating a kitchen, but let’s talk about something else that is equally powerful – cabinet hinges.

Based on this, you can then figure out the relationship between your cabinet doors and the frame or exposed edge of the cabinet—do the doors cover part of the frame or edge, or are they inset so that you can see that frame? Depending on whether it’s a single cabinet door or a double cabinet door, the frame or edge might be covered by one or two cabinet doors. 

Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.

For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
Excellent post! I already knew about the different options, but it’s so nice to see it all compiled in one place. 🙂 Very handy! I love the look (or rather, lack of) of concealed hinges… but roughly $10 a pair makes me cringe. If I’ve got about 20 doors, I’m looking at $200–for HINGES! The visible hinges run about $3, for $60 total. 🙁 Hmm… debating.
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
We were delighted with the professional quality of Meridian’s services. Your team was always responsive and courteous and went out of their way to ensure that our needs were met. Meridian worked closely with our architect to anticipate issues and deal with them in a timely manner. Our home was built in record time and we are very happy with the quality of workmanship.
Cup pulls add a unique style to drawers by going beyond the basic drawer handle. Whether you’re looking for a way to add antique or rustic style to your kitchen or you want to add modern flair, cup pulls enhance any décor. Since cabinet pulls are used frequently each day, look for quality metal styles that are durable and built to last. Cup pulls also come in interesting shapes and designs like leaves and clamshells to give your kitchen a fun aesthetic.
Consult with a contractor or a knowledgeable salesperson about which hinges will work with your doors. If your doors are flush with the cabinets, butt hinges can be used. They are lower in price than others but do not self-close. European hinges are installed on full overlay, frameless or inset doors. They are widely used because of their ease of installation and ability to be adjusted once in place. These hinges self-close. Partial wraparound hardware will support larger doors, but it does not self-close. Several other types hinges are available. The construction of your door, ease of installation and price will need to be considered. .
Mid-century modern design grew in popularity from the 1940s to the 1970s. During this time period, there was increased interest in nuclear physics, molecular chemistry, and science fiction which inspired the unique shapes seen in everything from furniture and lighting to homes and office buildings. Mid-century modern style combines vintage elements with sleek and timeless … Continued
Knikki Grantham is a Trend Manager with over 20 years in the Furniture and in the Furniture and Design Industry. She grew up in the furniture industry with early memories of sawdust and hand tied springs. After working in various phases of furniture production and development she moved into Design Sales for a Luxury high-end retailer, attaining an Associate ASID as well as other accreditations from various furniture manufacturers.

Our drawer pulls come in a nearly endless variety of materials, styles and finishes. For a contemporary, modern look, try a brushed nickel or chrome drawer pull. If you’re considering a more traditional, classic style, check out our bronze, brass, pewter and black drawer pulls. You’ll be amazed by how a small detail like cabinet hardware can change the look of an entire room. Updating kitchen cabinet hardware, or furniture hardware is also a quick and easy exercise that requires few tools, minimal effort, and is relatively inexpensive.


Under-cabinet lighting serves not only a fashionable purpose by creating visual depth in your kitchen, but it serves a functional purpose as well. The added lighting will make everything from chopping veggies to reading recipes to measuring ingredients easier to see as your countertops will be under direct light from above. And as far as style goes, the right lighting can make all the difference!
The other option for changing kitchen cabinet knobs is to purchase new ones. The two main types of cabinet fixtures for kitchens are circular pulls and metal bars. The round pulls tend to be old-fashioned, while the metal bar handles are often more contemporary. Cabinet pulls can be made more modern by painting them metallic silver. Metal bar cabinet door handles are usually silver-colored and narrow; this style is often seen with darker wood toned cabinets.
When it comes to finishes, let the rest of the components in the home be your guide. If you are selecting an oil-rubbed bronze artisan faucet, select the matching hardware. Interested in mixing finishes? In today’s home, anything goes. Mixing brass with black iron might be over the top, but pairing brushed nickel with polished chrome can offer a dynamic and attractive contrast.
When you’re choosing cabinet hardware, think about the number of times you’ll touch these pieces every day. If your cabinet pulls look and feel good and function well, you’re sure to derive pleasure from them. Browse our narrowed-down choices, from modern cabinet pulls to traditional knobs. Simply replacing your cabinet knobs is the easiest (and cheapest) way to spiff up a kitchen. Get started here.
You’ll also want to think about how visible your hinges will be—do you want them to be a major design feature and mounted directly to both the outside of the frame and the outside of the cabinet, known as a surface-mounted hinge? Or take a more minimalist design approach and have them virtually invisible from the outside when the cabinets are closed, known as a concealed hinge? Are you worried about the noise of cabinet doors closing, and think that soft-closing hinges are important? 

The chrome and stainless steel can vary some too, but usually not as much, and as often as nickel.  To be safe, get samples from different brands and compare the colors, or get all the hardware that you need for  a single room from one manufacturer.  It’s ok if the nickel in one room doesn’t exactly match the nickel in another room.  It only looks mismatched if the different nickel finishes  are right next to each other in the same room.
Thanks, Marty! You have a joyous looking kitchen/dining room – so beautiful! LOVE it! Not at all stiff and cookie-cutter, but with real individual style! An inspiration today. Your timing is perfect. We have our IKEA kitchen done, except for countertops and backsplash tiling. (We’ve been using Masonite board for a makeshift countertop. Not too bad.) The whole look of our open kitchen/dining room is pleasant, at this point, but bland. Pale minty-grass green walls, blonde (birch) cabinets, warm medium oak floors. Now for putting in some details! YAY! The scary part: Now what? Yikes!! Marty to the rescue with a reassuring article. THANKS! Here we go……
If you’re looking for a style that’s hot right now, look no further than modern cabinet hardware. This look features sleek, straight handles in horizontal lines, usually in a stainless steel or chrome finish. The hardware is skinny and will likely stand out against the color of your cabinetry. Another option is a rounded, long and vertical handle in the same finish.

One of the biggest enemies of a clean kitchen lies in careless cabinet hardware selection. Apart from choosing a gaudy color or ill-fitting shape, the one detail that can make or break the look of a cabinet door actually is the humble piece of hardware that is chosen to open and close it. From round knobs to long pulls and magnetic mechanisms, there’s a world of choices to make when it comes to honing in on the perfect hardware for kitchen cabinets. Some can stick out like a sore thumb, while others can be completely invisible.
“We find it refreshing for people to purchase what they like and what feels good to them, not caring what the ‘Joneses’ have,” says Renee. The Brandino Brass team regularly works with professionals who have their own signature styles. “One architect in town may use the same small knob all over the house all in the same finish for continuity. Another one will use different styles and finishes in each individual room,” says Jessie Isom, Brandino Brass team member. “There is no right or wrong if you like it.”
​If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go.  If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself.  If, however,  you decide on a warm metal faucets, door hinges or lighting fixtures,  many of us would have to hire a professional or handyman to replace those items.  But cabinet hardware can easily be switch out by almost anyone.  Just make sure you use standard sized hardware.
I thought for sure I’d go with the modern beauty on the upper right (the It Pull), but when I held them both up to the cabinets they whispered to me “go for the Bronte.” Like Shakira’s hips, cabinets don’t lie, so I went with the Bronte. Then we needed to chose the finish. As much as I lurrrrrrve gold hardware, my husband nixed that idea because he does not understand this is not the gold of the 1980’s. 😉 Since he gets very little choice in the rest of the house, I took one for the team (not really, I actually love the dark finish too) and chose the lovely Venetian Bronze finish. While gold would certainly have elevated this kitchen to on-trend status, I went for what works best for our marital harmony.

Once you’ve selected your new handles and pulls, it’s time to remove all the old ones. Using a drill or screwdriver, slowly back the screws out, then gently pull the old hardware away from the door or drawer front, so as not to damage the finish. Keep the old screws and pulls/knobs together in a plastic baggy so it’s easy to donate or toss them depending on their condition. If you’re going to repaint your cabinet doors, do it now.


Custom kitchen cabinetry doesn’t come cheap, but if you’re planning to stay put in your home for a long while, it’s worth spending to get exactly what you want, including the built-ins that enable you to live clutter-free. At the other end of the spectrum, we show you ways to modify Ikea kitchen components for a custom look (we’ve found almost a dozen new companies that offer doors to pair with Ikea’s cabinets).
Solid brass, bronze and stainless steel knobs are durable and long lasting, even under heavy use. If elegance is your thing, then opt for knobs made of crystal or marble to take your cabinet décor to the next level. These materials look sophisticated and classy. This simple change of replacing cabinet knobs is easy to implement on your own, and it will cost a whole lot less than replacing your cabinets entirely.
It's something you could DIY if you wanted to invest the time and energy into it, but I know my strengths and weaknesses. ;-). This sweet, retired woodworker, is charging $300-$400 to drill the holes in the cabinets, provide the hinges, and rehang them (all 23 of them), so I'm feeling like it's a pretty good deal, and the homeowner agrees! I'm really excited to see the finished look!

The chrome and stainless steel can vary some too, but usually not as much, and as often as nickel.  To be safe, get samples from different brands and compare the colors, or get all the hardware that you need for  a single room from one manufacturer.  It’s ok if the nickel in one room doesn’t exactly match the nickel in another room.  It only looks mismatched if the different nickel finishes  are right next to each other in the same room.

Pulling design from old pharmacies and soda fountains, latch hardware is that without a doubt a nostalgic throwback. Maybe not the most functional if you’re in a hurry, but handy if you’re looking for a little extra security from pets or children. Latches are another hardware type that can easily be mixed and matched, so maybe just keep them to the lesser used cabinets.
It’s important to choose hardware that will complement the rest of your kitchen décor and accentuate its worthy features. Generally, most people want their cabinet and drawer hardware to coordinate with the handles on their appliances. The colors should work well together, and the finishes shouldn’t clash. Drastically different shapes can also make your kitchen feel cluttered. You should use functionality and your personal preference to approach choosing knobs vs. pulls, but there are a few general guidelines to follow that correlate with your style of cabinets.

First, you’ll want to do a thorough count of all your doors and drawers to make sure you know exactly how many new pulls and knobs you’ll need. To streamline the project, match your new hardware’s spread to the distance between the existing screw holes (you may need a tape measure). Or you can just take one of the old pulls with you to the store to shop.
You don’t need to match your cabinet hardware finish to the rest of your kitchen. This is one area you can add a little bling. For example, we always recommend chrome faucets because chrome is the most durable (and in our experience, although popular, brushed nickel looks dingy and fingerprints are hard to remove), but consider brushed nickel or champagne gold for your cabinet hardware for a nice juxtaposition of metals in your kitchen
If you’re going for wood paneling, the process is pretty simple. Fasten the pieces together and cut to the size of your appliance. Then, remove the handles from your appliance and glue the panels onto the front using a hot glue gun. You can either paint the wood and the sides of your appliance to match your cabinets, or you can leave it as is for a natural unfinished feel. Complete the look by adding new appliance pulls to match the rest of your kitchen hardware. Appliance covers can be added to just about any kitchen appliance that has a door like a refrigerator and dishwasher.

Solid brass, bronze and stainless steel knobs are durable and long lasting, even under heavy use. If elegance is your thing, then opt for knobs made of crystal or marble to take your cabinet décor to the next level. These materials look sophisticated and classy. This simple change of replacing cabinet knobs is easy to implement on your own, and it will cost a whole lot less than replacing your cabinets entirely.
If you’re like me and love hardware (I think of it as jewelry for the house) and want your pulls and knobs to make a statement, instead of blend into background, you’ll want to choose hardware that contrasts with your cabinets, drawers and doors.  Consider using darker finishes like black or oil rubbed bronze on white or light colored cabinets and doors.  

Prior to making the purchase of your new cabinet hardware, take some careful measurements of the existing hardware. Write down sizes, as well as the spacing of the screws. This should eliminate the need to drill new holes. Accurate measurements are essential to avoid additional work or the need to return and exchange your hardware purchase. In fact, it is a good idea to bring some of your old hardware with you for size comparison purposes, unless you are shopping online for your hardware. In that case, simply have the hardware next to you.
I had already chosen polished nickel hardware (which I will share more about soon), so my hinges needed to coordinate.  I decided to use Rub n Buff to give them a much-needed update.  If you don’t know, Rub n Buff is a fantastic metallic paste used to give almost anything a metal finish.  I chose it because it is so easy to use and gives a lasting finish.
The choice between kitchen cabinet knobs and cabinet pulls and handles may seem unimportant, but knobs and handles have different features that can alter the overall look of your kitchen. Because kitchen cabinet knobs are round, they often give a kitchen a welcoming, home-style look that works especially well in country-themed kitchens. Kitchen cabinet handles and kitchen cabinet pulls, on the other hand, can give a kitchen a more sophisticated or elegant look. These distinctions are fairly loose though, and you can find plenty of rustic kitchen cabinet handles as well as sophisticated kitchen cabinet knobs, if that’s what you want.
​If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard.  To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space.  That way, each metal finish has coordinating partner in the same space.   Take a look at the 3 photos below.

Caring for decorative hardware purchased from Cliffside Industries is easy. Use only a soft cloth dampened with water for cleaning. The most important thing to remember is never to apply any chemicals or abrasive cleaners, including all kinds of soap or detergent. Using these products damages the protective lacquer and may change the appearance of the piece. Any use of chemicals, abrasives or soaps will void your warranty.
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
Thanks for stopping by Lovely Etc! While every effort has been made to ensure the accuracy and effectiveness of the information displayed on this website, Lovely Etc. makes no guarantees as to the procedures and information contained here. The publisher will not be liable for direct, indirect, incidental, or consequential damages in connection with the information displayed on lovelyetc.com. This website is not intended to substitute for advice from a professional. I work hard to be honest and upfront in all of my posts here at Lovely Etc., including sponsored content. Lovely Etc is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com. You can read my full disclosure policy here.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?

Over time, switch plates and outlet covers can become dingy and dirty. Replacing your old outlet covers is a quick way to add some new life to your kitchen décor. Switch plates and outlet covers are no longer stuck just being basic functional pieces on your wall. There are many different designs, materials and finishes that can complement the look of any room. Choose switch plates and outlet covers that are made from high-quality metal materials because they are more durable and stylish than basic plastic ones. Plus, you won’t have to worry about kitchen splatter creating unsightly stains on your covers, as this material is super easy to wipe clean!


Thanks, Marty! You have a joyous looking kitchen/dining room – so beautiful! LOVE it! Not at all stiff and cookie-cutter, but with real individual style! An inspiration today. Your timing is perfect. We have our IKEA kitchen done, except for countertops and backsplash tiling. (We’ve been using Masonite board for a makeshift countertop. Not too bad.) The whole look of our open kitchen/dining room is pleasant, at this point, but bland. Pale minty-grass green walls, blonde (birch) cabinets, warm medium oak floors. Now for putting in some details! YAY! The scary part: Now what? Yikes!! Marty to the rescue with a reassuring article. THANKS! Here we go……
There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
Want sleek form? Want functionality at its finest? Say hello to handles. Handles for white cabinets allow a firm and full grip to easily pull open or push close any cabinet door. Handles come in a cornucopia of shapes and sizes to male for a match with your kitchen style. Handles offer installation flexibility, with vertical and horizontal options, which allows for additional detailing for your white cabinets.
At one point I considered trying to update the cabinets with more modern hidden hinges, but after some research I realized that isn’t possible for all cabinet styles and can also be pretty costly.  So instead, I started making a plan to update the older-style hinges we already had.  They started out an aged brass finish.  And not a beautiful antique brass, but more like brass that had been soaking up kitchen grease for 40 years.  Not exactly what I wanted to use on my ‘new’ white cabinets.
Aesthetically when do you choose to a long handle or a cabinet door vs. a button size knob. This does require some finesse and doing some drawings to get it just right, but here are few tips to take into consideration. You may want to lean more towards small knobs and handles if you are going for a more contemporary style in your kitchen space. Often mixing and matching round knobs with drawer pulls work well in these style of kitchens. A longer handle may be used in a more modern kitchen for a more polished look in a space, while having too many small knobs would feel cluttered for this type of kitchen. In a transitional space, you may want to select one style of hardware and then make that one particular style of hardware larger or smaller depending on where it’s going in the kitchen. For example you would have larger handles for your refrigerator and pantry doors, but a smaller version of the same knob for the upper cabinets in your kitchen area above the refrigerator.
×