I mentioned to my super-smart carpenter brother, Mike, that I was wanting to update my hinges but was afraid of ruining my doors in the process.  I watched a YouTube video of DIYer who tried to install hidden hinges, and I’ll be polite and just say that the outcome was not a good one. Thus my fear. The place I ordered my new cabinets from couldn’t order replacement doors, so this was a one-shot deal.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!

The next step was to decide whether to go with pulls, knobs, or a combination of the two– and also the size. THIS WILL SEND YOU TO THE MADHOUSE if you’re not careful. To make my decision easier, I perused my kitchen ideas board on Pinterest and realized the look I was going for was modern and symmetrical– and many of the modern kitchen used only pulls, not knobs. Hmmmm, this was interesting. Maybe it wasn’t so hard to choose?
When updating your kitchen with new cabinet hardware, one of the easiest ways to achieve a cohesive look is to choose a matching hardware suite. By choosing a hardware suite, all of the guesswork of matching one piece to another is done for you. A hardware suite includes things like cabinet knobs, drawer pulls, door hinges and even window hardware — all with a similar finish and craftsman style.
Eight staircases?!?Nothing says 'stupid' quite as much as that!Not being critical of the crew, but between the 'historical society' that dictates what you can and can't do (but happily send you the bill) and over the top designs that will prove to be idiotic just makes me shake my head in disbelief.This certainly won't be a house where you can 'age in place'.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
Knikki Grantham is a Trend Manager with over 20 years in the Furniture and in the Furniture and Design Industry. She grew up in the furniture industry with early memories of sawdust and hand tied springs. After working in various phases of furniture production and development she moved into Design Sales for a Luxury high-end retailer, attaining an Associate ASID as well as other accreditations from various furniture manufacturers.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door. 
Cup pulls are a nice complement to Shaker-style cabinets, particularly in a country-style kitchen. Recessed hardware can make for a particularly elegant and modern look, but also tends to be a bit on the pricey side. Slim, modern finger pull type hardware, which mounts to the top of a drawer or the edge of a cabinet, is a nice choice for flat-front cabinets in a modern kitchen.

Apparently I would use MP(?) kind of boards (I forget what the man at HD called it) and it costs about $25 for an 8x4 sheet. I would just measure my cupboard doors, then go in and tell them the measurements, and they would do all the cutting. Then I would just prime the boards, then paint them, then pre-drill the holes for the new hinges, then put them up.
Knobs only: The benefit of cabinet knobs is that they are typically less expensive than bar and T-pulls, and they only require one hole to be drilled into your cabinetry. A single cabinet knob can be installed on cabinet doors, but you may want to consider placing two knobs on larger drawers. Cabinet drawers are heavier than doors, therefore you may need that extra knob for ease of use. The minimalistic style of using knobs only for your cabinetry can give a very appealing look to your new kitchen.
Dreamer, thinker, + lemon squeezer; you'll usually find me clutching a mug of coffee, glue gun, fandeck of paint colors, and a child at any given time. This mom of two (and wife to one) loves to share freshly squeezed ideas for home and family. Join the adventure as we learn most lemons can indeed become lemonade-- with generous amounts of sweetness, perspective, and love.
Our drawer pulls come in a nearly endless variety of materials, styles and finishes. For a contemporary, modern look, try a brushed nickel or chrome drawer pull. If you’re considering a more traditional, classic style, check out our bronze, brass, pewter and black drawer pulls. You’ll be amazed by how a small detail like cabinet hardware can change the look of an entire room. Updating kitchen cabinet hardware, or furniture hardware is also a quick and easy exercise that requires few tools, minimal effort, and is relatively inexpensive.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.
The first step in choosing kitchen hardware was to decide on the color and style. I fell in love with the selections offered by Atlas Homewares — so much so that I’m now thrilled to be partnering with them on this post. 🙂  I started by ordering several samples in various shapes, sizes and finishes so I could style them in person with the cabinets and countertops.

I can totally appreciate that.  You’ll notice that these cabinets are also flush with the cabinet frames, which makes the hinges a little less noticeable.  But sometimes, the hinge effect just isn’t quite as charming, and can be more distracting than anything.  A lot depends on what kind of cabinet overlay you’re dealing with and the aesthetic that you’re looking for in this sort of project. 


but wouldn’t the holes from the original overlay hinges show? I have stained maple cabinets and would love to get rid of the overly hinges but I have two problems. the holes will show, and also, the doors are smaller than what is typical for hidden hinges. All the kitchen cabinetry that I have seen with hidden hinges have cabinet doors that literally touch. inotherwords, they completely cover the cabinet. any suggestions? should I replace the doors? would I save money doing that?
The importance of selecting quality hardware is impossible to overstate. As with many parts of our home, hardware is an investment. We have all seen cabinet knobs that loosen too easily and hinges that wear out. Because hardware is going to receive the bulk of a cabinet’s wear and tear, investing more in it is ultimately investing more in the life of your cabinets.
And then there’s appliance hardware. Appliance pulls are not just hardware pulls that have a higher price point. It is a more durable hardware that look identical in style to your standard pulls, but are designed for the larger items in your kitchen like refrigerators, dishwashers, pantries, and oversized drawers. They come in a range of sizes from 6” to 36” and are constructed to hold a heavier weight, typically necessitating longer screws and a backplate for installation. The screws can be shortened to the needed size, but its best to follow the instructions and have these pieces installed by a professional to avoid hiccups.
×