“When it comes to hardware, it’s hard to shop on the internet,” says Eric. “Some things that look really good online, look cheap in person and vice versa. Some cheap-looking online items look exquisite in person.” The Brandino Brass team says that not only the look, but the feel of door hardware and cabinet hardware is very important. “You don’t want a handle to poke you or have an awkward grip for your hands,” says Renee.
Once you’ve selected your new handles and pulls, it’s time to remove all the old ones. Using a drill or screwdriver, slowly back the screws out, then gently pull the old hardware away from the door or drawer front, so as not to damage the finish. Keep the old screws and pulls/knobs together in a plastic baggy so it’s easy to donate or toss them depending on their condition. If you’re going to repaint your cabinet doors, do it now.
My home was built in 1940 and the kitchen cabinet hinges and pulls are the hammered black ones. I want to replace same pulls with chrome or polished chrome but cannot find the offset hinges or pulls to fit the holes. I really do not want to have to fill the holes to get another kind. Where can I find these? Have seen them in the past but now I cannot find them. Where should I look?
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
Concealed hinges can be mounted on the surface of the door or a pressed into a “cup” that is drilled into the door.  These are often called “cup hinges”.  The cup diameter is generally 35mm but that can vary as can the drill depth required to accept the hinge.  Most concealed hinges have built in adjustability so you can slightly change the position of the door without relocating the hinge.
Good morning and happy Monday, lovely people! I hope y’all had a wonderful Thanksgiving week. Ours was a little on the insane side, but it ended perfectly. We moved to our new house {Memaw’s house} a little over a week ago. It was crazy getting settled just in time to host our family’s Thanksgiving dinner. It was hard without Memaw. Tears came easily and our family time was just really sweet. I’m very thankful.
By adding hardware you like, you’re literally installing your style into the room — and this will make any accessories you want to add in feel like a part of the kitchen’s design, and not out of place. Of course, not every cabinet + hardware combo is going to work, but see how far you can take it when it comes to choosing hardware outside the traditional style of the cabinets.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
Furthermore, hardware attracts the eye like a bright light. Functionality aside, it is the ultimate accent piece — it provides a pop to cabinets and drawers that can make or break the décor of a room. It also keeps the wood of our cabinets and drawers looking fresh by taking the brunt of the natural oils in our hands, which we leave behind every time we reach for the cabinet to grab something.
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
We just moved into our home a few months ago and it definitely needed some updating. We decided to start in the kitchen with new appliances. Black stainless beauties 😍 That's when we really noticed how "80's" our kitchen cabinets were! They were in good shape, just wrong color. So we decided to just paint them! The hinges were terribly dirty with a film over them and brass colored. So here's a step by step how I quickly cleaned them and then painted them to match the black stainless appliances....
Mona Culberson began working on the assembly line at a large manufacturing company in 1983, where she worked her way up into several positions of business responsibility. In 2005, she began a career in roofing, interior design and remodeling. She works daily as a professional painter/home remodeler/handywoman while lending her husband's roofing business a helping hand in her spare time.
Our drawer pulls come in a nearly endless variety of materials, styles and finishes. For a contemporary, modern look, try a brushed nickel or chrome drawer pull. If you’re considering a more traditional, classic style, check out our bronze, brass, pewter and black drawer pulls. You’ll be amazed by how a small detail like cabinet hardware can change the look of an entire room. Updating kitchen cabinet hardware, or furniture hardware is also a quick and easy exercise that requires few tools, minimal effort, and is relatively inexpensive.

One of the most popular styles now is lacquered or aged brass. "Ten years ago," Huh says, "it was all about nickel: brushed nickel, shiny nickel. Now it's the resurgence of brass." Designers are using "bold tones, and things that look worn," she says, by installing unlacquered brass that tarnishes over the course of a year, or paying extra for "pre-antiqued" brass that already has a colorful patina.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
Nickel and chrome have about the same level of durability, but chrome is sometimes a bit more expensive.  Brushed or matte finishes hide fingerprints and watermarks better than shiny finishes.  You’ll generally find a lot more hardware options in brushed nickel than in chrome or stainless steel. Poor quality nickel and chrome finishes can peel and flake over time.  Stainless steel, which is usually matte, is the most durable of the silver finishes and as such, is usually the most expensive.  True stainless steel hardware is typically made from a full thickness metal alloy and it’s not just plated on the surface like nickel and chrome are. 
The style of cabinet hardware you pick will depend a great deal on the style of your kitchen, and also on the kind of cabinets you choose. Traditionally styled cabinets with more intricate face profiles call for traditional hardware: Cabinets with more simply styled or completely flat faces look best with minimal, streamlined knobs and pulls. Some very modern cabinets don’t require hardware at all: Instead, they have grooves on the edges of the door, or open by push latches.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!

The style of cabinet hardware you pick will depend a great deal on the style of your kitchen, and also on the kind of cabinets you choose. Traditionally styled cabinets with more intricate face profiles call for traditional hardware: Cabinets with more simply styled or completely flat faces look best with minimal, streamlined knobs and pulls. Some very modern cabinets don’t require hardware at all: Instead, they have grooves on the edges of the door, or open by push latches.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
The clean, industrial look of silver produces a calm ambiance, which pairs perfectly with your white cabinets. Silver is also bright enough, where it also stands out on your cabinets and gives your kitchen that shiny and sterile feel. The majority of today’s appliances are stainless steel, so your stainless steel hardware will share that uniform look.

Shake a can of rust-inhibiting metal spray primer for the amount of time recommended by the manufacturer. Position the can the recommended distance away from the hinges -- it varies among manufacturers. Spray a light coat of primer on the hinges and screw heads using steady, even sweeps. Make sure you spray the sides and edges. Shake the can frequently while you spray. Allow the primer to dry for the amount of time recommended by the manufacturer. Apply a second coat of primer and allow it to dry completely.


I watch you every Sunday morning. I used to help run a construction co. here in Knoxville,TN. I am now my Moms cargiver(87). I lost my dear sweet husband last November. I am trying to sale my house. I am just stressed trying to find replacement wrap-around hinges and pulls for my kitchen and bath. I also am going to replace my laminate tops. Do you have any sources I should check. You two remind me of my sweet dad and me from years ago. Please HELP!!!!!!

Caring for decorative hardware purchased from Cliffside Industries is easy. Use only a soft cloth dampened with water for cleaning. The most important thing to remember is never to apply any chemicals or abrasive cleaners, including all kinds of soap or detergent. Using these products damages the protective lacquer and may change the appearance of the piece. Any use of chemicals, abrasives or soaps will void your warranty.

After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!


You know I have read so many blogs, articles, and posts about this. I have even emailed some hardware companies like Rockler. I have a hinge that I can’t figure them out, I wanted to upgrade them to something more readily available as 5/8 partial inset hinges are hard to find. Rockler suggested replacing the cabinet doors. I spent over seven months working on redoing my kitchen cabinets.
“What is your overall style? Traditional, contemporary, arts and crafts, eclectic, cottage, French, Mediterranean, Western, Art Deco or coastal,” asks Brandino Brass co-owner Eric Brandino. He encourages clients to think about the style of their home or the style they would like to incorporate. “Is there a consistent style throughout or does it vary from room to room? Transitional style has been one of the most popular looks recently,” he says of what’s trending in hardware. “Clean lines with just a touch of traditional features and finishes, such as an unlacquered brass or bronze.”
There are a few options for hanging drawer hardware. Usually drawer pulls (or knobs or cup pulls) are centered on the face of the drawer. In a more modern kitchen, you may choose to hang them closer to the top of the face. For Shaker-style drawers, you can hang knobs or pulls either in the center of the drawer OR centered on the top stile. Which look should you go with? Whatever you like the best in your kitchen. Just make sure that you’re consistent across all the drawers. Drawers longer than two feet may look better with two knobs or pulls.
Thank you so much for helping me understand more about the process to choose new kitchen cabinet hardware. We have been really into rustic looking kitchens lately, and I think that some antique decorative nails could really change the way it looks. Just as you mentioned, you can always change the look of your kitchen again if you do not like the way it looks after a couple of years. Thanks for posting!

At a home renovation in Connecticut, cabinet fabricator Michael Madore experimented with what he calls an "aggressive" metal-sanding process to pull out the grain from the whitewashed oak plywood. For the hardware-free cabinets, Julie Salles Schaffer looked to a drawer pull detail derived from Giò Ponti’s work—though she admits the radial edging is an effect entirely her own.


Though not as common as stainless steel or brass, pewter is a very traditional western metal to use in a kitchen. It has a long history dating back around a thousand years — the “Worshipful Company of Pewterers” was even formed in 14th-century England to regulate pewter quality. By the time it began making its way onto furniture in the 1700s, it was a centuries-old art.

Specializing in hardwood furniture, trim carpentry, cabinets, home improvement and architectural millwork, Wade Shaddy has worked in homebuilding since 1972. Shaddy has also worked as a newspaper reporter and writer, and as a contributing writer for Bicycling Magazine. Shaddy began publishing in various magazines in 1992, and published a novel, “Dark Canyon,” in 2008.


In line with our new content direction, Architizer is highlighting a different building-product and how to specify it. This week’s topic is Kitchen Cabinetry. If you’re looking for the perfect kitchen cabinetry for your next project, search for it on Architizer’s new network marketplace for building-products. Click here to see if you qualify. It’s free for architects.
Also, experiment with different shapes. Things like knobs, handles, toilet paper holders, towel racks and hinges have a lot of expressive power. Beyond color, though, you should take advantage of their different shapes to accentuate certain features in a room. Pay attention to details like the width of drawers and the height of cabinet doors, and experiment with different shapes to complement them.
Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five.  I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
Cabinetmaker Steve Roca replies: Whether you're hanging new doors, as I'm doing here for a hallway cabinet, or swapping out old hinges, concealed or Euro-style hinges are a dream to install. Unlike the butt or knife hinges often used in kitchen cabinets, they can be adjusted along three axes with the turn of a screwdriver, so you can easily fine-tune the door's fit.
Although kitchen cabinet knobs are small objects, keep in mind that one on each cupboard door creates an overall design impact. Further impact can be created by choosing cabinet knobs that contrast in color and texture with the cabinets. If less impact is desired, cabinet knobs may be made of the same material and in the same color as the kitchen cabinets. The most important thing to remember when choosing cabinet knobs to coordinate with cabinets is to keep the kitchen’s overall tone in mind, whether it’s country, elegant, whimsical or traditional.
If you’re looking for a more contemporary approach, tubular bars seem to be a favorite of the future. The current design couples beautifully with darker finishes and larger tiles. Tubular bars can also be used horizontally or vertically, and can be as long or short as you like. Go with a shorter bar for a more modest appeal, or make a statement with longer ones.
What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.

What they are: Art objects as much as pulls, these knobs draw attention. Placed in the center, they draw your eye to the detailing of the worn wood here. Search salvage yards for antique ones and don’t be afraid to spring for the few knobs you’ll need. If you can’t find this sort of door detailing, you can create a similar effect by placing a medallion behind each knob in the center of your doors. Look for antitwist pins to keep the knob from spinning (in fact, do this with any round knob).

In line with our new content direction, Architizer is highlighting a different building-product and how to specify it. This week’s topic is Kitchen Cabinetry. If you’re looking for the perfect kitchen cabinetry for your next project, search for it on Architizer’s new network marketplace for building-products. Click here to see if you qualify. It’s free for architects.

Order samples, and get a few different types of styles and sizes to decide what will work best for your cabinet doors. It’s helpful to shop with a sample of your cabinet door. Ask yourself: Does my hand keeps sliding on the grip? Is it difficult to pull or get a grasp on it? Does it get greasy from my fingertips? Would I rather have a pull near the fridge but a knob near the stove? You will use this item a ton of times everyday, and you want to feel comfortable with your choice. There’s nothing worse than a cute knob that’s hard to pull open everyday.
×