Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
One of the biggest enemies of a clean kitchen lies in careless cabinet hardware selection. Apart from choosing a gaudy color or ill-fitting shape, the one detail that can make or break the look of a cabinet door actually is the humble piece of hardware that is chosen to open and close it. From round knobs to long pulls and magnetic mechanisms, there’s a world of choices to make when it comes to honing in on the perfect hardware for kitchen cabinets. Some can stick out like a sore thumb, while others can be completely invisible.
You don’t need to match your cabinet hardware finish to the rest of your kitchen. This is one area you can add a little bling. For example, we always recommend chrome faucets because chrome is the most durable (and in our experience, although popular, brushed nickel looks dingy and fingerprints are hard to remove), but consider brushed nickel or champagne gold for your cabinet hardware for a nice juxtaposition of metals in your kitchen
Your kitchen is looking beautiful. White paint is a miracle worker…so are you. I have an old 1970’s GE oven that looks just like yours. It’s a great oven and still works perfectly. I had the door, which was originally light brown, re-enameled years ago when I painted my kitchen white. It’s held up beautifully. I just wish I had two ovens like yours. Sure would come in handy for holiday cooking.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Knob or pull? Bronze or silver? Small or big? Kitchen cabinet hardware is more than just a pretty decoration; knobs and pulls keep your cabinet cleaner and protect the finish. Plus, while they’re little, they can actually make a big impact on your kitchen’s appearance. But with thousands of options out there, how can you select the right hardware to make the best impact? Take these things into consideration before you make your final kitchen cabinet hardware selection.
For pulls on a flat front cabinet, the bottom corner of the pull should be equidistant from both sides of the cabinet. For Shaker-style cabinets, the same rules apply as with knobs: center the pull on the vertical stile, with the bottom of the pull even with the top of the horizontal stile (or the top even with the bottom of the horizontal stile, for a lower cabinet). These aren’t hard and fast rules—you may want to adjust them depending on what looks best for your cabinets and hardware—but they’re a good place to start.
You may also have seen cabinets that are so modern and minimalist that they have no knobs or pulls whatsoever—and they look like they’re impossible to open! The trick is, in fact, a mechanism with a spring located on the inside of the cabinet. When you push on the corner of a cabinet, you compress and then release the spring, which in turn pops the cabinet open. In order to close the cabinet, you simply push it closed until you hear the little "click" that means the spring is back in its locked position.
Wow! I finally figured out what to ask for, THANKS. Old hickory cabinets still look great, and the wife loves them, but hates the sound of them closing. Want soft closing hinges, a nice project. They are face-frame cabinets, with semi-inset doors with about 1/4″ overlay.and inset about 3/8″. What hinges do I need? Plan on doing this just as soon as the soft closing drawer slides are all installed.
The importance of selecting quality hardware is impossible to overstate. As with many parts of our home, hardware is an investment. We have all seen cabinet knobs that loosen too easily and hinges that wear out. Because hardware is going to receive the bulk of a cabinet’s wear and tear, investing more in it is ultimately investing more in the life of your cabinets.
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening.
Thanks Mary. That is a good question. There is another similar product from DecoArt called Metallic Lustre but I am not sure if it is available in Europe either. (Also, I haven’t used it so I can’t say for sure if I would recommend it.) Also, it isn’t exactly the same but silver spray paint can also work. After cleaning the hinges, spray them with spray primer and then follow up with a spray paint in the metallic finish you want.
The size of your cabinets will influence the size of your knobs. If your cabinets are smaller in scale you’ll want to opt for hardware that is likewise, such as minimal-scale circular knobs. Longer hardware is necessary when you have extra long cabinet doors—or can be used if you want to make a more of dramatic statement. Most cabinet doors are 24”, so you want a knob about 2”-3” size knob. For a larger cabinet door you can size up to 3½” or 4”. For a cabinet door under 20”, source hardware that’s closer to 1” to 2” size in diameter or length.