Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
You know I have read so many blogs, articles, and posts about this. I have even emailed some hardware companies like Rockler. I have a hinge that I can’t figure them out, I wanted to upgrade them to something more readily available as 5/8 partial inset hinges are hard to find. Rockler suggested replacing the cabinet doors. I spent over seven months working on redoing my kitchen cabinets.
Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five. I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door.
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
Cabinet hardware is a great way to show off your personality and refresh your home. Use classy drawer pulls or colorful cabinet knobs to add style to your bedroom, kitchen or bathroom, or any room in the house. Choose from modern, farmhouse, classic and contemporary styles. Although knobs and pulls can be used interchangeably, knobs are usually used on doors and pulls on drawers.
Hopefully you drilled for the hinges in the same location on every door, if so, then this should be simple. You really just need to measure for the top hinge. I installed my top hinge 4” down from the top of the door, so I measured 3 ½” down from the inside top of the face frame (3 ½” + ½” overlay = 4”). This step is a team effort, one person to hold the door and another person to attach the hinge to the face frame.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
There it is, our top 16 knobs and pulls. We were surprised there weren't any on-trend satin brass options on the list. While we've seen an up-tick in brushed and satin brass hardware's popularity, these tried-and-true stainless steel, satin nickel, and oil rubbed bronze knobs and pulls are still leading of the pack. It just goes to show that not everyone is a trend-follower. Choose your kitchen design details based on your tastes, because the trends will always change anyway!