Hanging knobs on a flat-front cabinet is pretty straightforward: You’ll want to position the knob in the bottom corner (for upper cabinets) or top corner (for lower cabinets) of the door. Knobs should be placed equidistant from both sides of the cabinet. A guide like this one can help you to get the measurements right. The exact distance will depend on the look you want and the size of your knobs: Test one or two before you drill a whole kitchen’s worth of holes.
Are your cabinets in good condition but old, worn out and dated looking (kind of like me!)? With just a few tweaks you can bring them into this century and get another 10 to 15 years of life out of them. It seems like back in the 70s and 80s kitchen cabinets were built on site and built to last! That’s the case with the kitchen I’m currently dealing with, the entire kitchen was site built, they made one long face frame for an 8’ bank of cabinets – picture all the face frames of your cabinets connected together and installed as one piece, that’s how this kitchen is. Anyway, I was happy with the layout, it’s pretty basic, so to save some money I decided to work with the existing cabinets by removing the valance, replacing the exposed hinges with concealed hinges and adding glass inserts to the upper, upper cabinets – you’ll see what I mean in a minute. If you have ever thought of updating your dated kitchen cabinets, you’ll definitely want to check out this article in all its splendor.
From round and oval to square and rectangle, cabinet knobs come in all types of shapes and sizes. Show off your personal flair for design with novelty cabinet knobs. If you’re going for a coastal look, we have novelty cabinet knobs shaped like sea shells, starfish and sea horses. If you have a child who plays sports, we’ve got you covered with soccer, baseball and basketball shaped cabinet knobs. We also carry antique cabinet knobs for history lovers.
This step will work best with raised panel or recessed panel cabinets, my cabinets are raised panel. OK, so I have a little confession to make, I outsourced this step, my routering skills are not top notch and I wanted the kitchen to look good, not like something put together by Dr. Frankenstein. The good news is it was very inexpensive and I was able to get 10 little doors done for less than the cost of a new upper cabinet. If you’re an ace with the router then you know exactly what to do, so have at it!
Prevent cabinet doors from slamming shut with integrated Prevent cabinet doors from slamming shut with integrated soft-close technology from Everbilt. Designed for a full overlay these hinges are retro fit able and allow any level DIYer to do away with the heavy slamming of cabinet doors. The complete overlay leaves your cabinets with a sleek modern look. More + Product Details Close
Hidden hinges also come in a soft-close style if you’re one of those people who want the latest and greatest. (Is it really that bad to hear a door close?) My new cabinets came with soft close hinges that I personally could take or leave. I still find myself trying to shut them all the way instead of letting them do their thing. You might not want soft-close hinges if you’re the type who likes to slam things when irritated. (Just a thought.)
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
For oversized cabinetry you’ll obviously want to use larger hardware. Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized. For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches. Some contemporary pulls are even larger than 12 inches. That measurement is taken from the center of one screw hole to the center of the second screw hole). Oversized knobs are 1-1/2” or larger.
These industrial-feeling pulls are a blend of colonial and Arts and Crafts, and come in a wide variety of finishes. While these black ones are a good choice with the black appliances and lighting, don’t feel your knobs must match all the finishes in your kitchen; it’s OK to mix things up. Just don’t mix the knobs and hinges on the same door; those definitely should be coordinated so one doesn’t detract from the other.
Prior to making the purchase of your new cabinet hardware, take some careful measurements of the existing hardware. Write down sizes, as well as the spacing of the screws. This should eliminate the need to drill new holes. Accurate measurements are essential to avoid additional work or the need to return and exchange your hardware purchase. In fact, it is a good idea to bring some of your old hardware with you for size comparison purposes, unless you are shopping online for your hardware. In that case, simply have the hardware next to you.
Due to its quasi-metallic makeup, crystal does much more than just sparkle — it also exhibits other coveted traits. When rubbed to the point of vibrating, crystal will produce a musical tone. It is also stronger than glass and can be blown quite thin. Cliffside Industries distributes German crystal, which is stupendous in its clarity and diamond-like cuts, as well as products from the world-famous Austrian crystal maker Swarovski AG.
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
The first step in choosing kitchen hardware was to decide on the color and style. I fell in love with the selections offered by Atlas Homewares — so much so that I’m now thrilled to be partnering with them on this post. 🙂 I started by ordering several samples in various shapes, sizes and finishes so I could style them in person with the cabinets and countertops.
I have a solid oak kitchen from the late 1980s. I would like to update the cabinets by painting them but my hinges are exposed. Is it possible to change any exposed hinge to a hidden hinge, or are there some styles that won't be replaceable? Also, has anyone else painted kitchen cabinets with exposed hinges in such a way that it looks good? Thanks!
Let’s talk first about metals. As a general rule, I like to keep the different metals in a kitchen to no more than two. If you have stainless steel appliances, that counts as one metal. So that leaves one other metal you can bring into a kitchen. If you’ve got brass light fixtures, that’s your one other metal. Your new hardware should be nickel or brass.