I’m currently on the hunt for the perfect brass pulls to update my run-of-the-mill silver knobs. But to get a whole sense of what's available at the hardware store these days, I'm looking beyond just brass and test-driving a few other options as well. From handsome black bars to boho porcelain and even DIY leather, these gorgeous hardware options are sure to inspire.

Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.

Due to its quasi-metallic makeup, crystal does much more than just sparkle — it also exhibits other coveted traits. When rubbed to the point of vibrating, crystal will produce a musical tone. It is also stronger than glass and can be blown quite thin. Cliffside Industries distributes German crystal, which is stupendous in its clarity and diamond-like cuts, as well as products from the world-famous Austrian crystal maker Swarovski AG.


At this point, you will have narrowed down your hardware choices to a specific style, type, size and finish. Next thing to incorporate is your budget. A good starting point is to count how many knobs and pulls you will need for your cabinetry and determine a price range that is comfortable for you. Many hardware manufacturers have multiple lines of varying quality and price, so be sure to find a manufacturer that uses high-quality materials. Buying cheap can seem like a good idea in the short run, but cheaper metals will degrade faster down the road and face a much higher risk of breaking or bending. Stainless steel hardware, for example, should be solid (not hollow) with a durable but even finish.
One of the biggest enemies of a clean kitchen lies in careless cabinet hardware selection. Apart from choosing a gaudy color or ill-fitting shape, the one detail that can make or break the look of a cabinet door actually is the humble piece of hardware that is chosen to open and close it. From round knobs to long pulls and magnetic mechanisms, there’s a world of choices to make when it comes to honing in on the perfect hardware for kitchen cabinets. Some can stick out like a sore thumb, while others can be completely invisible.

Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.


For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.
2. Keep finishes cohesive. You’ll find hardware in a range of finishes from brushed nickel to brass. While mixing and matching the hardware around your kitchen is fine, you should try to maintain the same finish and keep colors as close as possible. Sometimes you’re forced to buy hardware from more than one retailer, but when doing so make sure you keep finishes cohesive.
It’s definitely possible to change out the hinges without redoing the cabinets – you would just have to make sure that the holes on the frames where the old hinges were, are able to be filled and touched up so that they’re not obvious. I’m not sure of the cost, but hinges aren’t cheap, and I definitely recommend using a carpenter to do the work. Hinges can be maddening!
Most knobs and pulls are only a few dollars apiece but when you consider the sheer number that you’ll need, those costs add up fast. For each standard lower cabinet with two doors and one drawer, you’ll need three pieces of hardware — and two more knobs or pulls for the matching upper cabinet doors. With that in mind, here are a couple of factors to consider:
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
This was a great project! I did something similar but much lazier. After installing beautiful brushed-nickel handles to dozens of drawers & cupboards, I noticed that the 30 year old hinges were dark brown and ornate (against white cabinets). Yuck ... So I opened each cabinet & used painter's tape to block off a rectangular area around each hinge. They weren't dirty, so I just painted inside the whole rectangle with silver paint. The result is sleeker and more modern, and nobody would ever notice unless they were really close. Love it!
For knobs on a cabinet with a stile, like Shaker-style cabinets, allow the stile to be a guide for hanging the knob. If the knob is too large to comfortably fit in the corner where the two stiles meet, then hang the knob centered on the vertical stile, with the bottom edge of the knob aligned with the top of the intersecting horizontal stile. (Or the top of the knob aligned with the bottom of the stile, for lower cabinets). The knobs in this kitchen from Ivory Lane are a good example.
Budget is, of course, a key factor in any part of your kitchen remodeling decisions. While you’ll want to pay as little as possible right now, remember that quality matters in the long run. Your local kitchen cabinet showrooms will offer you the largest variety, with people who can help you choose high-quality hardware within your budget. Remember that the price is based on the finish, as well as the design and size. Knobs are less expensive than pulls.
For pulls on a flat front cabinet, the bottom corner of the pull should be equidistant from both sides of the cabinet. For Shaker-style cabinets, the same rules apply as with knobs: center the pull on the vertical stile, with the bottom of the pull even with the top of the horizontal stile (or the top even with the bottom of the horizontal stile, for a lower cabinet). These aren’t hard and fast rules—you may want to adjust them depending on what looks best for your cabinets and hardware—but they’re a good place to start.
For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.

The color white, and more specifically, white colored cabinets, have never been more popular in today’s kitchens. White is always in style, regardless if you have a slick modern kitchen or relaxed country style. With their relaxed style and design flexibility, it’s no secret as to why white cabinets are a constant crowd pleaser. The color white can make a room look larger and timeless in one broad stroke. With white cabinets, hardware is the most crucial detail, as it is more than just an accent, Hardware completes the room and adds overall value to your kitchen. With all of the available options, selecting the perfect hardware for your white cabinets can be a frustrating exercise. Below we discuss what to consider when selecting hardware for white kitchen cabinets.
If your old fridge still runs like a champ on the inside but it’s starting to look like a but run-down and haggard on the outside, spruce it up with a DIY custom cover! Appliance covers are fastened directly to the outside of your appliance, masking their appearance on the outside and making them blend in with your kitchen cabinetry. You can take materials like bead board paneling, wallpaper, wood from old pallets or even mismatched wood scraps from barns to create an interesting look for your old appliance.

The clean, industrial look of silver produces a calm ambiance, which pairs perfectly with your white cabinets. Silver is also bright enough, where it also stands out on your cabinets and gives your kitchen that shiny and sterile feel. The majority of today’s appliances are stainless steel, so your stainless steel hardware will share that uniform look.


Once you’ve worked out which types of hardware are comfortable to use, it’ll be time to start thinking about shapes in relation to the shape of your cabinetry. In general, knob and pull styles should be matched to kitchen cabinet styles. What this means is if you have selected a plain cabinet style, for example, shaker or flat, ultra-modern doors, then you’ll want square, plain hardware to match — perhaps something like Emtek’s brass bar knob or a similar style. Recessed panel doors or doors with curving and intricate trim will often do well with more ornate hardware styles.
Dreamer, thinker, + lemon squeezer; you'll usually find me clutching a mug of coffee, glue gun, fandeck of paint colors, and a child at any given time. This mom of two (and wife to one) loves to share freshly squeezed ideas for home and family. Join the adventure as we learn most lemons can indeed become lemonade-- with generous amounts of sweetness, perspective, and love.
These industrial-feeling pulls are a blend of colonial and Arts and Crafts, and come in a wide variety of finishes. While these black ones are a good choice with the black appliances and lighting, don’t feel your knobs must match all the finishes in your kitchen; it’s OK to mix things up. Just don’t mix the knobs and hinges on the same door; those definitely should be coordinated so one doesn’t detract from the other.
I watch you every Sunday morning. I used to help run a construction co. here in Knoxville,TN. I am now my Moms cargiver(87). I lost my dear sweet husband last November. I am trying to sale my house. I am just stressed trying to find replacement wrap-around hinges and pulls for my kitchen and bath. I also am going to replace my laminate tops. Do you have any sources I should check. You two remind me of my sweet dad and me from years ago. Please HELP!!!!!!
My home was built in 1940 and the kitchen cabinet hinges and pulls are the hammered black ones. I want to replace same pulls with chrome or polished chrome but cannot find the offset hinges or pulls to fit the holes. I really do not want to have to fill the holes to get another kind. Where can I find these? Have seen them in the past but now I cannot find them. Where should I look?

Mid-century modern design grew in popularity from the 1940s to the 1970s. During this time period, there was increased interest in nuclear physics, molecular chemistry, and science fiction which inspired the unique shapes seen in everything from furniture and lighting to homes and office buildings. Mid-century modern style combines vintage elements with sleek and timeless … Continued
Cabinet hardware is composed a variety of materials -- most of which are metal alloys. Brass hardware typically has a lacquer or plating applied to its surface that makes it very durable in a kitchen. It is antimicrobial and helps to reduce the spread of germs. Bronze hardware is also antimicrobial, offers a substantial look and feel, and works well for cabinets made of thicker woods. Stainless steel is another option because it is so durable. Pewter and nickel are popular choices, too. Or, you can choose knobs made from glass or crystal for a vintage look. 
Cup pulls are a nice complement to Shaker-style cabinets, particularly in a country-style kitchen. Recessed hardware can make for a particularly elegant and modern look, but also tends to be a bit on the pricey side. Slim, modern finger pull type hardware, which mounts to the top of a drawer or the edge of a cabinet, is a nice choice for flat-front cabinets in a modern kitchen.
There it is, our top 16 knobs and pulls. We were surprised there weren't any on-trend satin brass options on the list. While we've seen an up-tick in brushed and satin brass hardware's popularity, these tried-and-true stainless steel, satin nickel, and oil rubbed bronze knobs and pulls are still leading of the pack. It just goes to show that not everyone is a trend-follower. Choose your kitchen design details based on your tastes, because the trends will always change anyway!
×