What is the existing decor of your kitchen or bathroom? For instance, if your kitchen has a white, Scandinavian minimalist aesthetic, you should try matching your hardware with it — in that case, perhaps something slender, jet-black and low-profile. Mismatching styles can look “off” and can create a confused sense of the room’s personality. However, it can also be done well. We’ll go into more depth on this below.
If you like the idea of mixing metals, just make sure that the mix looks intentional instead of haphazard. To make your design of mixed metals look intentional, choose 2 or 3 metal finishes and use those finishes in at least 2 or 3 areas within the space. That way, each metal finish has coordinating partner in the same space. Take a look at the 3 photos below.
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
Aesthetically when do you choose to a long handle or a cabinet door vs. a button size knob. This does require some finesse and doing some drawings to get it just right, but here are few tips to take into consideration. You may want to lean more towards small knobs and handles if you are going for a more contemporary style in your kitchen space. Often mixing and matching round knobs with drawer pulls work well in these style of kitchens. A longer handle may be used in a more modern kitchen for a more polished look in a space, while having too many small knobs would feel cluttered for this type of kitchen. In a transitional space, you may want to select one style of hardware and then make that one particular style of hardware larger or smaller depending on where it’s going in the kitchen. For example you would have larger handles for your refrigerator and pantry doors, but a smaller version of the same knob for the upper cabinets in your kitchen area above the refrigerator.
Now comes the fun part, place the point of the forstner bit in the center hole you marked earlier and start drilling, drill the holes ½” deep, that’s the thickness of the bit. The instructions on the back of the kit say “do not drill completely through the door,” Ummm, OK… You’ll want to do this twice on every door, 36” or 42” doors may need 3 hinges each. Let’s backtrack a little here, when you remove the doors mark them and the cabinet box so you’ll know where they go back. Now, do that over and over and over again until all your doors are finished.
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
Fantastic, right? Now, think about how much busier the cabinets would look if they still had the exposed hinges. Granted, with polished chrome hardware, it would minimize the hinge effect, but suppose you like oil rubbed bronze hardware? Exposed hinges of that variety would really stand out against the clean white cabinets. Having hidden hinges gives you the freedom to change hardware on a whim.
Recessed Pulls mimic the utilitarian style of traditional office cabinetry. They’re built into the cabinet door and can be crafted from the same material to blend in or a contrasting material to highlight their presence. They’re also great for high-traffic kitchens because they don’t protrude from the doors, meaning there is little risk of them snagging on clothing.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
By adding hardware you like, you’re literally installing your style into the room — and this will make any accessories you want to add in feel like a part of the kitchen’s design, and not out of place. Of course, not every cabinet + hardware combo is going to work, but see how far you can take it when it comes to choosing hardware outside the traditional style of the cabinets.
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
One of the most popular styles now is lacquered or aged brass. "Ten years ago," Huh says, "it was all about nickel: brushed nickel, shiny nickel. Now it's the resurgence of brass." Designers are using "bold tones, and things that look worn," she says, by installing unlacquered brass that tarnishes over the course of a year, or paying extra for "pre-antiqued" brass that already has a colorful patina.
For Shaker-style cabinets, look for hardware like small round knobs or hardware that feels organic to the craftsman style. I like the idea of brushed nickel or brass for this style of cabinetry. With modern fronts, choose hardware with a sleek and simple design, think matte black or stainless steel, or don’t be afraid to ignore hardware all together and have a custom groove built-in. When planning for a more traditional approach, push the boundaries in your hardware and look for more ornate knobs.