Latches for cabinets aren’t quite as common as they were about a 100 years ago because of improved hinge technology, but you can still find a variety of latches and catches for keeping cabinets closed. A latch is mounted to the outside of a cabinet, and typically features two pieces: a mechanism with a turn or a lever on one side that controls the "tongue" of the latch, and a "shell" with a cavity to house the tongue on the other side. On the other hand, cabinet catches are usually installed on the inside of a cabinet, making them invisible from the exterior, and can consist of a magnet, a clip, or a ball that holds the door closed unless a certain amount of force is applied to open it.

Below and above the sink can be two different color schemes. Don’t worry, you can mix and match more than you might think and still obey the laws of symmetry. It can provide a sunny, uplifting splash to have a lighter color above the level of the countertops, such as a warm brass or gold. Particularly with items like faucets and sconces, a lighter color around eye level will create a happy glow.
Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.
What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
Over time, switch plates and outlet covers can become dingy and dirty. Replacing your old outlet covers is a quick way to add some new life to your kitchen décor. Switch plates and outlet covers are no longer stuck just being basic functional pieces on your wall. There are many different designs, materials and finishes that can complement the look of any room. Choose switch plates and outlet covers that are made from high-quality metal materials because they are more durable and stylish than basic plastic ones. Plus, you won’t have to worry about kitchen splatter creating unsightly stains on your covers, as this material is super easy to wipe clean!
For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
With each pass of the roller and swipe of my paint brush I am making my way around the kitchen. Going back to standard time has slowed me down since it gets dark around 5 o’clock now. I like to paint in daylight, using electrical lights casts too many shadows and I miss spots. It is also getting colder outside. I was painting in the garage, but the temps have to be above 50 to paint, so I brought my painting set-up inside.
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.

What they are: Art objects as much as pulls, these knobs draw attention. Placed in the center, they draw your eye to the detailing of the worn wood here. Search salvage yards for antique ones and don’t be afraid to spring for the few knobs you’ll need. If you can’t find this sort of door detailing, you can create a similar effect by placing a medallion behind each knob in the center of your doors. Look for antitwist pins to keep the knob from spinning (in fact, do this with any round knob).

What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?
Do you dream of a whole-kitchen remodel straight out of a magazine photo spread? Kitchens begin to look dated more quickly than any other room in your home. Replacing cabinets and countertops is an expensive proposition, but what if you could update them just a bit at little cost? Replacing or adding new cabinet hardware is a great way to update your look with the latest finishes and styles, without breaking open the piggy bank.
There’s no hard and fast rule on how long bar pulls should be, so go with personal preference. However, most designers keep them at two-thirds to three-quarters the width of the drawer. Notice they’re even longer in this kitchen, yet the length works. A good idea is to purchase a few knobs and pulls, bring them home and try them out before replacing your entire kitchen’s hardware.

What if you can’t decide on kitchen hardware? It’s OK to mix and match! Pick patterns and finishes that complement each other and install them in a repeating pattern for a look that is custom to your style. It’s easy to switch up this look as you please. However, this might not impress a potential homebuyer if you choose to sell in the future. Consider updating to more traditional cabinet hardware when it comes time to sell.


Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.
Picking the perfect cabinets for a project is hard enough, but the effort it takes to research, test and finally decide on the best piece of outward-facing cabinet hardware calls for even further inspection. While the main material for the cabinet door heavily contributes to a kitchen’s character, its hardware serves to accentuate that character further still. A key detail within one of the most important spaces of a residence, cabinet hardware sits squarely at the intersection of form and function, and making the right choice here can elevate the design of the entire kitchen.
Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
Once you know whether you want cabinet handles or cabinet knobs and which sort of design you want, you’ll want to choose a material and finish. Cabinet pulls and handles come in a variety of materials, from inexpensive plastic to high-end polished brass. As a general rule, nickel or stainless steel cabinet handles usually give a more modern, sophisticated look to a kitchen, whereas bronze and brass handles often project an antique or rustic look. Most materials come in different finishes, from glossy polishes to dark antique finishes, so you’re sure to be able to find something that matches your kitchen decor.
On the very last warm-ish day of the year, I laid out all the drawers and doors and got my painting on with my paint sprayer. That thing is the bomb! I had them all primed with Zinsser oil based primer within 15 minutes. Then I waited a couple of hours before painting the final coats. I used Sherwin Williams oil based ProEnamel in Alabaster for the upper cabinets and Sherwin Williams contractor grade oil based paint color matched to Benjamin Moore’s Huntington Green.
Custom kitchen cabinetry doesn’t come cheap, but if you’re planning to stay put in your home for a long while, it’s worth spending to get exactly what you want, including the built-ins that enable you to live clutter-free. At the other end of the spectrum, we show you ways to modify Ikea kitchen components for a custom look (we’ve found almost a dozen new companies that offer doors to pair with Ikea’s cabinets).
First, you’ll want to do a thorough count of all your doors and drawers to make sure you know exactly how many new pulls and knobs you’ll need. To streamline the project, match your new hardware’s spread to the distance between the existing screw holes (you may need a tape measure). Or you can just take one of the old pulls with you to the store to shop.
Linda, great questions! I have only had my rub n buffed hinges in use for a few weeks so far so I can’t say much for long term use yet. I can say that I haven’t had a problem with it rubbing off, but I did have to be really careful hanging my cabinet doors because I noticed that it did rub off on the white paint if I wasn’t careful. (The few spots where that happened, I just touched up the white paint.) I also didn’t have a problem getting it to shine – but I was going for a brushed nickel look which isn’t super shiny. I don’t know that you could get it shiny enough to be a chrome looking finish. Overall I have been really happy with it but I will be sure to share an update after more time passes.
But If you don’t think of your hardware as decorative (but as purely functional) and just want your pulls and knobs to blend into the background, instead of standing out, you can choose hardware that is more subtle.  Choose dark hardware for darker cabinets or silver or clear hardware for white or light cabinets.   Alternatively, you can forgo cabinet pulls and knobs all together, which will give a much more contemporary  look.
1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
I’m Jenny, a wife of 23 years, mother of three, and a corporate drop-out. I’m a creative minded blogger, business owner and DIYer, and love transforming furniture, cabinets and rooms in my home. I’m a card carrying paint geek, and am always amazed at the power of paint in making budget-friendly updates to your home. I’m a serial house-stalker, and never tire of a great home tour or a before and after renovation. I’m a firm believer in restyling, refreshing and renewing things in your home to make it your own - without breaking the budget. I’ll show you how!

One of the biggest enemies of a clean kitchen lies in careless cabinet hardware selection. Apart from choosing a gaudy color or ill-fitting shape, the one detail that can make or break the look of a cabinet door actually is the humble piece of hardware that is chosen to open and close it. From round knobs to long pulls and magnetic mechanisms, there’s a world of choices to make when it comes to honing in on the perfect hardware for kitchen cabinets. Some can stick out like a sore thumb, while others can be completely invisible.


What kind of new hardware should you install in your updated kitchen? There are so many choices out there it can be overwhelming. Knobs or Pulls? Nickel or Brass? Will you be able to see the holes from the old hardware? Because I am being asked these questions on a daily basis I’ve put together a general guide to updating hardware and have included some of my favorites to share with you.
×