Budget: Get an idea of the full scope of your makeover project first. Then get an idea of how much of that budget can go toward your door and cabinetry hardware. The cost of individual pieces can be broad, as hardware can be produced by many methods. Material and intricacy of the handle itself affect price as well. A Gross Electric hardware expert will help you get the most bang for your buck.
3. Traditionally, your hardware should be the same finish as your kitchen sink faucet. However, mixing and matching metals is on trend in contemporary and transitional homes. Don’t forget to consider your appliances and light fixtures as well. Black appliances look lovely beside bronze or black hardware, while stainless steel and nickel play nicely together.
Caring for decorative hardware purchased from Cliffside Industries is easy. Use only a soft cloth dampened with water for cleaning. The most important thing to remember is never to apply any chemicals or abrasive cleaners, including all kinds of soap or detergent. Using these products damages the protective lacquer and may change the appearance of the piece. Any use of chemicals, abrasives or soaps will void your warranty.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.
There is a lot of misunderstanding when it comes to crystal. Upon first glance, it looks like glass, but it is in fact of higher quality and clarity, and its chemical composition is markedly different. Contrary to what its name suggests, crystal is not crystalline on a molecular level — that is, its molecules are not arranged in a rigid, repeating structure.
So here’s how this works. On the new cabinets I ordered, the center of the hinges were 4 1/2″ from the bottoms and the tops of the doors, so that’s the measurement I used for drilling on my old doors. The original hinges on the old cabinets were placed at about 3″ from the ends, so I didn’t have to worry about the old holes interfering with my new ones.
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
Do you dream of a whole-kitchen remodel straight out of a magazine photo spread? Kitchens begin to look dated more quickly than any other room in your home. Replacing cabinets and countertops is an expensive proposition, but what if you could update them just a bit at little cost? Replacing or adding new cabinet hardware is a great way to update your look with the latest finishes and styles, without breaking open the piggy bank.
I've painted lots of golden oak cabinets in three houses now! Hidden hinges also called European hinges are a huge update. You have to take hinges off to paint anyway so instead of putting the old ones on you can fill the holes and replace them with European style hinges. There is a special type of drill bit that counter sinks an appropriate sized hole to accept the European hinge. It would be easy to find at a big box store along with the hinges themselves.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
The importance of selecting quality hardware is impossible to overstate. As with many parts of our home, hardware is an investment. We have all seen cabinet knobs that loosen too easily and hinges that wear out. Because hardware is going to receive the bulk of a cabinet’s wear and tear, investing more in it is ultimately investing more in the life of your cabinets.
What is the existing decor of your kitchen or bathroom? For instance, if your kitchen has a white, Scandinavian minimalist aesthetic, you should try matching your hardware with it — in that case, perhaps something slender, jet-black and low-profile. Mismatching styles can look “off” and can create a confused sense of the room’s personality. However, it can also be done well. We’ll go into more depth on this below.
I'm a wax girl. Wax always seems to work best for me and I'm ok with reapplying every 6 months or so. With that said, I cleaned them really good krud cutter. It's a great degreaser. Then sanded them first with 120 grit, then 180 grit, and finally 220 grit. Then cleaned them again with the vinegar/water mixture. I always have a spray bottle with the mix handy. Once dried, I primed and painted followed by waxing.
Based on this, you can then figure out the relationship between your cabinet doors and the frame or exposed edge of the cabinet—do the doors cover part of the frame or edge, or are they inset so that you can see that frame? Depending on whether it’s a single cabinet door or a double cabinet door, the frame or edge might be covered by one or two cabinet doors.
Your kitchen is coming along really well, and all that lovely light will be an absolute joy! Sadly, I have just a word of warning about the handles though. We had these in our kitchen, and they proved quite annoying. They’d catch on your clothing, especially blouses/shirts. That end of the front of button-through blouses, where the seam folds back would always get hooked onto the end of the handles! And pockets, too would get caught. This invariably ended up with torn clothing, as you continued to move away, not realising you’d been ‘caught’. We also live near the sea, and ours rusted over a few years, although that may be just an inferior brand. I lived with ours for about 4 years, then changed them all. We had them in our bathrooms, too, and they’ve all been changed as they were such a pain! I can see you love them, so don’t want to burst your bubble, but just thought I’d let you know. :(
If you’re going for wood paneling, the process is pretty simple. Fasten the pieces together and cut to the size of your appliance. Then, remove the handles from your appliance and glue the panels onto the front using a hot glue gun. You can either paint the wood and the sides of your appliance to match your cabinets, or you can leave it as is for a natural unfinished feel. Complete the look by adding new appliance pulls to match the rest of your kitchen hardware. Appliance covers can be added to just about any kitchen appliance that has a door like a refrigerator and dishwasher.
Your kitchen is looking beautiful. White paint is a miracle worker…so are you. I have an old 1970’s GE oven that looks just like yours. It’s a great oven and still works perfectly. I had the door, which was originally light brown, re-enameled years ago when I painted my kitchen white. It’s held up beautifully. I just wish I had two ovens like yours. Sure would come in handy for holiday cooking.
1. Stick with the theme. The hardware you choose speaks to your theme in the same way your kitchen cabinets do. Which hardware works best with different themes? Sleek, tubular pulls, like those in our Torino collection, complement the streamlined look in modern and contemporary kitchens. Traditional cabinets tend to have more detail and benefit from simple, smooth knobs, like the Projectionin style from our Drake collection. French country can benefit from hardware with an antique look, like our Windermere collection that comes in gun metal, rubbed bronze and brush pewter.
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.