Knobs are installed with a single screw through one focused entry point on a door or drawer. Pulls are installed with two screws through two points of contact on a door or drawer. Before any holes are drilled, make sure you give detailed instructions to your homebuilder or remodeling professional so that they know the correct type of handle to install on each cabinet door or drawer. You will also need to specify the position of the knob or pull so that they are installed in a consistent manner throughout the kitchen.
Between your cabinets and your drawers, you may have thirty of more cabinet handles in your kitchen, which has a significant effect on the look of the room, so you will want to choose knobs and pulls that match or complement your kitchen decor. If your kitchen has a modern look, consider choosing a cabinet handle that has angles and a very simple design or a square knob. Keep in mind that you can find knobs and pulls in a number of different designs, so if you have a Tuscan-themed kitchen, you can find kitchen cabinet knobs stamped with grapes, and if you have a rustic kitchen, you can find kitchen cabinet handles made from twisted wrought iron.
SimplyBeautifulKitchens.com is a participant in the Amazon Services LLC Associates Program and other affiliate programs, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com and other merchants websites. You should always perform due diligence before buying goods or services online. The Owner does not accept payment or merchandise from manufacturers in exchange for writing reviews.
2) I also note that it does not take long before doors start to sag & the gaps become irregular. Not hard to fix just lie on your back, take all doors off, then tighten everything & replace – then take a cold shower you will need it! It seems the cup sections remain well fixed but the fixing plates on the inside of the cupboard sides just work loose. This ought not to happen but it does & with all the concealed overlay hinges I have seen. Is there an answer? I suspect the hinges are under rated, 2 hinges for doors that typically are nearly 10Lbs may be the reason. Can you please comment.

Disclaimer: Although it is my intention to provide accurate plans and clear instructions, not all plans have been tried and tested. Using plans or information found on SawdustGirl.com indicates that you agree with the Terms of Use policy and will accept full responsibility for the process and outcome of any project you attempt. All plans are for private use only. Plans and information published on SawdustGirl.com may not be reproduced, republished or distributed in any manner without written permission from Sandra Powell, Sawdust Girl. Actual projects built using Sawdust Girl plans may be published on your own site without instructions or "tutorial" as long as you provide a link to my original post with full post title or "SawdustGirl.com" as link title.


When it comes to designing a kitchen inevitably you have to pick out hardware, and these seemingly small details can literally keep you up at night, going back and forth between brass knobs or stainless steel bars. But thankfully, we’re here to help you get a “handle” on the process. Here are the factors you should consider when choosing kitchen cabinet hardware.
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
Wow, love the progress you’ve made ! Thank you so much for these posts , your ideas are wonderful and I love your style. The drawer pulls are lovely, just what I had in mind, but the glass knobs ? What a lovely idea, I have glass knobs on my interior doors, but hadn’t thought of using them on kitchen cabinets . LOVE it . Can’t wait to see the finished kitchen, what an amazing difference .
Let’s talk first about metals. As a general rule, I like to keep the different metals in a kitchen to no more than two. If you have stainless steel appliances, that counts as one metal. So that leaves one other metal you can bring into a kitchen. If you’ve got brass light fixtures, that’s your one other metal. Your new hardware should be nickel or brass.
×