You may also have seen cabinets that are so modern and minimalist that they have no knobs or pulls whatsoever—and they look like they’re impossible to open! The trick is, in fact, a mechanism with a spring located on the inside of the cabinet. When you push on the corner of a cabinet, you compress and then release the spring, which in turn pops the cabinet open. In order to close the cabinet, you simply push it closed until you hear the little "click" that means the spring is back in its locked position.
Your kitchen is coming along really well, and all that lovely light will be an absolute joy! Sadly, I have just a word of warning about the handles though. We had these in our kitchen, and they proved quite annoying. They’d catch on your clothing, especially blouses/shirts. That end of the front of button-through blouses, where the seam folds back would always get hooked onto the end of the handles! And pockets, too would get caught. This invariably ended up with torn clothing, as you continued to move away, not realising you’d been ‘caught’. We also live near the sea, and ours rusted over a few years, although that may be just an inferior brand. I lived with ours for about 4 years, then changed them all. We had them in our bathrooms, too, and they’ve all been changed as they were such a pain! I can see you love them, so don’t want to burst your bubble, but just thought I’d let you know. :(
Go to the home improvement center and get a 35mm Concealo Hinge mounting kit, it comes with a forstner bit (invented by Benjamin Forstner, in case you didn’t know) and a jig for marking the drill location. You’ll also want to make sure you get 35mm European-style hinges too, but before you buy them you’ll need to determine if you have ½” overlay or full overlay doors. ½” overlay doors overlap the face frames by a ½”, full overlay doors fully overlap the face frame leaving about an 1/8” showing on the outside edge. My doors were all ½” overlay, so I bought eighty 3-way adjustable hinges from eBay. I’m not sure what I was thinking because I ended up with a LOT of hinges left over. Warm up your drill and let’s move on to the next step.
Custom kitchen cabinetry doesn’t come cheap, but if you’re planning to stay put in your home for a long while, it’s worth spending to get exactly what you want, including the built-ins that enable you to live clutter-free. At the other end of the spectrum, we show you ways to modify Ikea kitchen components for a custom look (we’ve found almost a dozen new companies that offer doors to pair with Ikea’s cabinets).

When updating your kitchen with new cabinet hardware, one of the easiest ways to achieve a cohesive look is to choose a matching hardware suite. By choosing a hardware suite, all of the guesswork of matching one piece to another is done for you. A hardware suite includes things like cabinet knobs, drawer pulls, door hinges and even window hardware — all with a similar finish and craftsman style.


Your kitchen is coming along really well, and all that lovely light will be an absolute joy! Sadly, I have just a word of warning about the handles though. We had these in our kitchen, and they proved quite annoying. They’d catch on your clothing, especially blouses/shirts. That end of the front of button-through blouses, where the seam folds back would always get hooked onto the end of the handles! And pockets, too would get caught. This invariably ended up with torn clothing, as you continued to move away, not realising you’d been ‘caught’. We also live near the sea, and ours rusted over a few years, although that may be just an inferior brand. I lived with ours for about 4 years, then changed them all. We had them in our bathrooms, too, and they’ve all been changed as they were such a pain! I can see you love them, so don’t want to burst your bubble, but just thought I’d let you know. :(
I can totally appreciate that.  You’ll notice that these cabinets are also flush with the cabinet frames, which makes the hinges a little less noticeable.  But sometimes, the hinge effect just isn’t quite as charming, and can be more distracting than anything.  A lot depends on what kind of cabinet overlay you’re dealing with and the aesthetic that you’re looking for in this sort of project. 

Kitchen knobs, pulls, and hinges have come a long way from the traditional styles that have been available over the years. No longer are homeowners limited to plain, simple, and functional. Instead, functional and pretty can now go hand in hand. Today’s styles include finishes in antique copper, iron, nickel, polished chrome, aged bronze, polished brass, glass, stainless steel, and antique brass. Additionally, a variety of knobs, handles, and pulls are available in ceramic styles.

Knob or pull? Bronze or silver? Small or big? Kitchen cabinet hardware is more than just a pretty decoration; knobs and pulls keep your cabinet cleaner and protect the finish. Plus, while they’re little, they can actually make a big impact on your kitchen’s appearance. But with thousands of options out there, how can you select the right hardware to make the best impact? Take these things into consideration before you make your final kitchen cabinet hardware selection.


Order samples, and get a few different types of styles and sizes to decide what will work best for your cabinet doors. It’s helpful to shop with a sample of your cabinet door. Ask yourself: Does my hand keeps sliding on the grip? Is it difficult to pull or get a grasp on it? Does it get greasy from my fingertips? Would I rather have a pull near the fridge but a knob near the stove? You will use this item a ton of times everyday, and you want to feel comfortable with your choice. There’s nothing worse than a cute knob that’s hard to pull open everyday.
There are a couple of ways to go about choosing the right color and finish. One school of thought advises you to choose based on the color and finish of the kitchen’s faucet. Given that most faucets are either silver or brass in color, this advice can be limiting, especially if you have your eye on stone knobs or another finish that is not common in faucet design.
I had already chosen polished nickel hardware (which I will share more about soon), so my hinges needed to coordinate.  I decided to use Rub n Buff to give them a much-needed update.  If you don’t know, Rub n Buff is a fantastic metallic paste used to give almost anything a metal finish.  I chose it because it is so easy to use and gives a lasting finish.
Good morning and happy Monday, lovely people! I hope y’all had a wonderful Thanksgiving week. Ours was a little on the insane side, but it ended perfectly. We moved to our new house {Memaw’s house} a little over a week ago. It was crazy getting settled just in time to host our family’s Thanksgiving dinner. It was hard without Memaw. Tears came easily and our family time was just really sweet. I’m very thankful.
Another type of door hardware for opening cabinets are pulls or handles, which are attached to cabinet door fronts with two or more screws. You may have had experiences where you were trying to swap out old cabinet pulls for new ones, say, for example modern glass cabinet hardware, only to realize that the pulls had two screws that were a different distance apart from the new ones that you purchased. Don’t worry—you’re not alone! This happens often because the distance between two screws varies depending on pull type, manufacturer, and other factors.
For this step you’ll want to clamp your door to the work surface, unless of course you want your door to spin around in circles and possibly punch you in the stomach. Next, measure equal distance from the top and bottom of the door and mark the center hole with the jig, also mark the 2 side holes where you’ll screw the hinge in place (I found that using an awl to mark the holes made it easier to drill). We drilled for our hinges over the same location as the old ones, which were NOT equal distance from the top and bottom, but at least every door was at the same unequal distance.
Hi, Randi! I love all your comments. They are MAKING my day! (Especially how can I be old enough to have a daughter with her own place lol This daughter also has two kids which makes me grandma. Oy. Yes, I’m THAT old!) Anyway, I’m so glad you commented and shared about your kitchen. I’m so glad you’re going for what you want! Sometimes we do indeed get paralyzed but we have to remember who our homes are for…..and that’s US! I think we want to enjoy our kitchen especially, since most of us spend time in there with our families, or at least cooking for our families!
Pre-drilled holes: replacing the handles on cabinets comes with a few more limitations than selecting completely new cabinetry – namely that the holes might be pre-drilled. You must make sure the center measurements of the existing holes match the spacing of the new pieces. Standard hole center measurements for pulls are 96 mm, 128 mm, 160 mm, 192 mm. When choosing the size of the hardware, keep in mind the scale in relation to the size of your cabinets. Regarding door handles, there is a good chance you may need to increase the size of the bore hole in your door as well. The old standard size was 2-1/8” diameter, and the new standard size is 2-3/8” or 2-3/4”. Tutorials The Quick Door Hanger can help you learn how to do this with a boring bit.
I love your site and your super helpful advice. We’re installing full overlay cabinets in our kitchen and we’re trying to select hinges for the upper cabinets — particularly the cupboard doors on the end which when closed is perpendicular to a wall. Since the door aren’t inset, I’m concerned we won’t be able to open the cupboard a full 90 degrees. Basically, the issue is how to solve the problem of the door swing? Are there any hinges that could solve this problem? I can send elevations if that helps. Thanks so much in advance!
Consult with a contractor or a knowledgeable salesperson about which hinges will work with your doors. If your doors are flush with the cabinets, butt hinges can be used. They are lower in price than others but do not self-close. European hinges are installed on full overlay, frameless or inset doors. They are widely used because of their ease of installation and ability to be adjusted once in place. These hinges self-close. Partial wraparound hardware will support larger doors, but it does not self-close. Several other types hinges are available. The construction of your door, ease of installation and price will need to be considered. .

For knobs on a cabinet with a stile, like Shaker-style cabinets, allow the stile to be a guide for hanging the knob. If the knob is too large to comfortably fit in the corner where the two stiles meet, then hang the knob centered on the vertical stile, with the bottom edge of the knob aligned with the top of the intersecting horizontal stile. (Or the top of the knob aligned with the bottom of the stile, for lower cabinets). The knobs in this kitchen from Ivory Lane are a good example.
I did a little google search to see what color my oven (and sink and cooktop and bathroom) used to be. It was called Mexican sand. I also once had olive green washer, dryer, freezer and refrigerator. Oh my, we thought we were really stylin’ back in the good old 70’s. I cringe when I see a photo of myself in the fashion of the day too. I miss my youthful look, but not the styles.
Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
Mona Culberson began working on the assembly line at a large manufacturing company in 1983, where she worked her way up into several positions of business responsibility. In 2005, she began a career in roofing, interior design and remodeling. She works daily as a professional painter/home remodeler/handywoman while lending her husband's roofing business a helping hand in her spare time.
Based on this, you can then figure out the relationship between your cabinet doors and the frame or exposed edge of the cabinet—do the doors cover part of the frame or edge, or are they inset so that you can see that frame? Depending on whether it’s a single cabinet door or a double cabinet door, the frame or edge might be covered by one or two cabinet doors. 
Finally, another popular way of opening cabinets without the use of traditional pulls or knobs is through cut-outs in the cabinetry. These are frequently found on custom cabinets where a minimalist look is desired, or where the budget is tight and saving on hardware is desirable. Cut-outs can come in a range of shapes, and are often designed to facilitate ease of opening. 

From round and oval to square and rectangle, cabinet knobs come in all types of shapes and sizes. Show off your personal flair for design with novelty cabinet knobs. If you’re going for a coastal look, we have novelty cabinet knobs shaped like sea shells, starfish and sea horses. If you have a child who plays sports, we’ve got you covered with soccer, baseball and basketball shaped cabinet knobs. We also carry antique cabinet knobs for history lovers.


I am thinking of doing similar here but can’t find the Harbor Freight Brad Nailer he used (electric as I am not gonna drag the huge air compressor to this house from our shop!) And some of the reviews I have seen on other brad nailers have been less than confidence inspiring! Any suggestions as to a decent plug-in nailer—don’t need the “staple” function JUST the nails!
For oversized cabinetry you’ll obviously want to use larger hardware.  Oversized cabinets and drawers are defined as over 3 feet wide. Cookware drawers or built-in appliance cabinetry are usually oversized.  For these large drawers and cabinet doors, consider long pulls which typically come in widths of 6”, 8”, 10” or 12 inches.  Some contemporary pulls are even larger than 12 inches.  That measurement is taken from the center of one screw hole to the center of the second screw hole).  Oversized knobs  are 1-1/2” or larger.
Due to its quasi-metallic makeup, crystal does much more than just sparkle — it also exhibits other coveted traits. When rubbed to the point of vibrating, crystal will produce a musical tone. It is also stronger than glass and can be blown quite thin. Cliffside Industries distributes German crystal, which is stupendous in its clarity and diamond-like cuts, as well as products from the world-famous Austrian crystal maker Swarovski AG.
Mid-century modern design grew in popularity from the 1940s to the 1970s. During this time period, there was increased interest in nuclear physics, molecular chemistry, and science fiction which inspired the unique shapes seen in everything from furniture and lighting to homes and office buildings. Mid-century modern style combines vintage elements with sleek and timeless … Continued
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
Cup pulls add a unique style to drawers by going beyond the basic drawer handle. Whether you’re looking for a way to add antique or rustic style to your kitchen or you want to add modern flair, cup pulls enhance any décor. Since cabinet pulls are used frequently each day, look for quality metal styles that are durable and built to last. Cup pulls also come in interesting shapes and designs like leaves and clamshells to give your kitchen a fun aesthetic.
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
Based on this, you can then figure out the relationship between your cabinet doors and the frame or exposed edge of the cabinet—do the doors cover part of the frame or edge, or are they inset so that you can see that frame? Depending on whether it’s a single cabinet door or a double cabinet door, the frame or edge might be covered by one or two cabinet doors. 

I’m currently on the hunt for the perfect brass pulls to update my run-of-the-mill silver knobs. But to get a whole sense of what's available at the hardware store these days, I'm looking beyond just brass and test-driving a few other options as well. From handsome black bars to boho porcelain and even DIY leather, these gorgeous hardware options are sure to inspire.
×