The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.
Remodeling and customizing your kitchen can be a big project. After planning and designing on the large scale it might be tempting to coast through choosing the cabinet hardware, but high-traffic rooms such as kitchens deserve detailed attention. Choosing the right hardware size requires a balance of style and function. Sacrifice one for the other, and you probably won’t be happy. You’ll be frustrated every time you try to pull open a drawer, or you’ll be disappointed every time you walk into the room.
Thanks, Marty! You have a joyous looking kitchen/dining room – so beautiful! LOVE it! Not at all stiff and cookie-cutter, but with real individual style! An inspiration today. Your timing is perfect. We have our IKEA kitchen done, except for countertops and backsplash tiling. (We’ve been using Masonite board for a makeshift countertop. Not too bad.) The whole look of our open kitchen/dining room is pleasant, at this point, but bland. Pale minty-grass green walls, blonde (birch) cabinets, warm medium oak floors. Now for putting in some details! YAY! The scary part: Now what? Yikes!! Marty to the rescue with a reassuring article. THANKS! Here we go……
One popular subset of modern drawer cabinet pulls are cup pulls, sometimes also known as half-moon pulls because of their half-circle form. Rather than wrap your fingers around a bar, as is the case with most pulls, users slip their fingers in the underside of a cup handle, pulling towards themselves. A similar but even more modern version of this is the finger pull, where a U-shaped pull gets installed to the inside edge of a drawer, leaving an L-shaped pull that your fingers slide under. These two types of modern cabinet pulls are installed using a specific mounting method, and they can only be installed in one direction, facing down.
If you’re like me and love hardware (I think of it as jewelry for the house) and want your pulls and knobs to make a statement, instead of blend into background, you’ll want to choose hardware that contrasts with your cabinets, drawers and doors.  Consider using darker finishes like black or oil rubbed bronze on white or light colored cabinets and doors.  
For those considering putting their home on the market soon, it’s likely your looking at what parts of your home to freshen up to impress potential buyers. Changing your cabinet hardware to a traditional option can make a huge difference. Small, ridged handles in a dark finish or square knobs is a cabinet hardware pick that will stand the test of time.
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
Modern cabinet door hinges are a critical part to any cabinet, and are also quite complex; there are about a dozen (if not more) different types of hinges, depending on whether you have face-frame cabinets or frameless cabinets. Face-frame cabinets include a frame made of 1-½" to 2" wide solid wood that attaches to the front edges of the cabinets. This type of cabinet construction is common in American-made cabinets, and hinges will then mount directly to this frame. However, if you have frameless cabinets—which are typically made in Europe, like IKEA cabinets—your cabinets are basically just a four-sided box with no frame around the front edges. In this case, the hinges will mount directly to the interior of the cabinet. 
When updating your kitchen with new cabinet hardware, one of the easiest ways to achieve a cohesive look is to choose a matching hardware suite. By choosing a hardware suite, all of the guesswork of matching one piece to another is done for you. A hardware suite includes things like cabinet knobs, drawer pulls, door hinges and even window hardware — all with a similar finish and craftsman style.
Generally speaking, I like to see a combination of knobs and handles/pulls. Knobs or handles for the doors and handles or pulls for the drawers. If you are painting your kitchen, the extra holes can be filled, sanded, and smoothed prior to painting so you can start with a clean slate and choose any hardware for your update. I say “generally speaking” because lately I’m drawn to kitchens that have all handles like this “before” photo of a kitchen we recently updated.
×