What they are: Sturdy yet glamorous pulls that complement many styles of cabinetry. Here linear flat bar pulls not only underscore the contemporary feel of the kitchen, but oversize pulls eliminate the need for two pulls on a wide drawer. A good rule of thumb is to use two knobs or pulls on drawers 18 inches wide or wider. But if you choose superwide pulls like these, one is enough.
Some pulls and handles are specifically made for appliances like refrigerators, dishwashers, and other appliances where you might have panels installed on the front of the item to match the surrounding cabinetry. Typically, appliance handles and pulls have been designed to higher standards than traditional, mid-century, or modern cabinet drawer pulls because they need to withstand more wear and tear—your fridge door has suction that resists opening, and you probably open the fridge more times than most of the cabinets in your kitchen. As a result, many appliance handles and pulls are larger, wider, or thicker than similar cabinet hardware.
Consult with a contractor or a knowledgeable salesperson about which hinges will work with your doors. If your doors are flush with the cabinets, butt hinges can be used. They are lower in price than others but do not self-close. European hinges are installed on full overlay, frameless or inset doors. They are widely used because of their ease of installation and ability to be adjusted once in place. These hinges self-close. Partial wraparound hardware will support larger doors, but it does not self-close. Several other types hinges are available. The construction of your door, ease of installation and price will need to be considered. .
The quick answer is yes, you can change the hinges. The hard part is what type. Cabinet doors have lots of different configurations.....full overlay, partial overlay, inset, etc., etc. The hinges have to fit the door style. There are hidden hinges that screw to the cabinet framework without major holes, and there are European type hinges that require a large hole to set the hinge into. Go to big box and look at the hinges, what is available can be mind boggling, until you understand the type of door you have.
What they are: An upside-down cup-shaped pull popularized in the mid-19th century. Bin or cup pulls are a popular choice for giving a kitchen a minimalist, vintage feel, just like on these Shaker-style cabinets and drawers. Shakers originally used wood pegs, usually made from maple, cherry or pine, in keeping with their preference for simplicity and austerity. But these cup-shaped drawer pulls are considered Shaker style today, and look clean and understated along with small knobs for the doors.
You don’t need to match your cabinet hardware finish to the rest of your kitchen. This is one area you can add a little bling. For example, we always recommend chrome faucets because chrome is the most durable (and in our experience, although popular, brushed nickel looks dingy and fingerprints are hard to remove), but consider brushed nickel or champagne gold for your cabinet hardware for a nice juxtaposition of metals in your kitchen
In my opinion, going to a specialty showroom and paying the extra expense is worth it, because you’ll find choices outside the mainstream and you can get expert help there. These come from the selection at The Plumbery, a kitchen and bath fixture store in Northern California. Here you can see glass knobs, swirly knobs, modern knobs — all just a tad pricier than conventional choices at a hardware store. But look at the workmanship and style, even the heft. Though the average kitchen has 20 to 40 knobs, you might want to splurge for something unique.
When choosing a backsplash color scheme, keep in mind the type of look you want for your kitchen. By choosing a backsplash color that blends in with your wall color, you’ll be creating a streamlined, coordinated look. If you want to make a statement and have your backsplash pop, try choosing one or even a few colors that accent your wall color, making it stand out from the background.
The cons are a few: 1. MDF is heavy in relation to wood or plywood. 2. MDF does not accept screws very well. You must use coarse thread screws and always pre-drill. Apply the hinge screws by using a hand-held screwdriver instead of a screw gun. If you don't, they can strip the hole quickly. 3. Over time the screws will come lose just from opening and closing the doors (just go around every so often and tighten the screws). 4. If water gets into the doors, they will swell and they will need to be replaced so seal them well.
When updating your kitchen with new cabinet hardware, one of the easiest ways to achieve a cohesive look is to choose a matching hardware suite. By choosing a hardware suite, all of the guesswork of matching one piece to another is done for you. A hardware suite includes things like cabinet knobs, drawer pulls, door hinges and even window hardware — all with a similar finish and craftsman style.
Most of your pulls and knobs, though, will go on standard sized cabinetry, which will be 3 feet wide or less. The most common pull sizes for standard cabinetry are 3”, 4”, or 96mm and 128mm, again measured from the center of one screw hole to the center of the other. But many of today’s pulls tend to be on even larger than 4 inches. Standard knob sizes are less than 1.5 inches in diameter.
Modern cabinet door hinges are a critical part to any cabinet, and are also quite complex; there are about a dozen (if not more) different types of hinges, depending on whether you have face-frame cabinets or frameless cabinets. Face-frame cabinets include a frame made of 1-½" to 2" wide solid wood that attaches to the front edges of the cabinets. This type of cabinet construction is common in American-made cabinets, and hinges will then mount directly to this frame. However, if you have frameless cabinets—which are typically made in Europe, like IKEA cabinets—your cabinets are basically just a four-sided box with no frame around the front edges. In this case, the hinges will mount directly to the interior of the cabinet.
Apparently I would use MP(?) kind of boards (I forget what the man at HD called it) and it costs about $25 for an 8x4 sheet. I would just measure my cupboard doors, then go in and tell them the measurements, and they would do all the cutting. Then I would just prime the boards, then paint them, then pre-drill the holes for the new hinges, then put them up.
5. Be aware of the appliances and fixtures in the kitchen. Pulls and knobs are not the only hardware in your kitchen. Take into account the finish on appliances, light fixtures, and your sink and faucet. While mixing metal finishes is trendy right now in kitchen design, be sure not to overdo it. If the colors clash, it could disrupt the cohesiveness of your kitchen and take away from the beauty of your new cabinets.
When decorating your rustic kitchen, a little bit of detail can go along way! There are many round, cast iron options that have designs that look great in rustic kitchens. If cast iron is too dark for your cabinets, look for an antique pewter finish. The detail within the hardware itself will certainly add to the look. This option also works well for a farmhouse style kitchen, giving it a great country feel.
Do you dream of a whole-kitchen remodel straight out of a magazine photo spread? Kitchens begin to look dated more quickly than any other room in your home. Replacing cabinets and countertops is an expensive proposition, but what if you could update them just a bit at little cost? Replacing or adding new cabinet hardware is a great way to update your look with the latest finishes and styles, without breaking open the piggy bank.
Hardware makes an enormous difference in the bones of the cabinetry and the style of the room. If I was facing down an oak kitchen that I wanted to live with, in harmony, for a bit of time, here’s what I would do in one weekend: Paint it a great color. Clear the counters. Lay down a great, eye-catching rug. Change out the hardware. Add some color (probably a big framed print and a huge plant in a nice planter). That’s it.
Wow, its looking great and really coming together. Did you use stick on tiles for the kitchen? I too have ugly hinges and have to tackle them. Do I just contact the hardware company and describe what I have? The cabinets in my home appear to be handmade by the original owner but the hinges are the black iron wrought look that was so popular back in the day. Love the glass cabinet knobs too!
After the center panels have been removed, take measurements of the inside openings. I subtracted an 1/8” from the length and width just to make sure the glass would fit. Now, go to Lowes, find the glass cutting isle and give the kind man or woman working there your list of measurements. Make sure you have other things to shop for because this is going to take a while, but it’s super duper cheap so it’s worth the wait. By the way, you don’t have to use glass, you could use that cool radiator metal, chicken wire, punched tin, you name it, sky’s the limit!
Chrome, nickel and stainless steel finishes will never go out of style, but warm metallics offer a fresh, modern look. For a quick update, consider replacing your lighting, faucet or cabinet hardware with products in gleaming brass or bronze like the ones in this chic space. “The updated satin brass cabinet hardware is really striking against the simple shaker cabinets,” says designer Elizabeth Lawson.