Hi Angie, I think that over time the rub n buff would rub off of the hardware from repeated touching. My hinges still look good two years later, but I can still see places where the finish is starting to rub off and the hinges are almost never touched. I do think that you could update your hardware with a good spray paint though. Just be sure to clean them thoroughly and use a spray primer followed by spray paint. I have update furniture hardware this way that is still going strong almost 10 years later. Good luck!
For customers who have homes near the ocean, Cliffside recommends choosing non-metal items such as marble or wood for your projects. Salt air acts as an abrasive, and quickly erodes the lacquer coating. If you absolutely need (or desire) metal hardware, Cliffside recommends solid stainless steel, or certain solid brass finishes such as Black, Polished Brass, or Polished Chrome. Note that, even in optimum indoor conditions, no Cliffside finish has a lifetime guarantee under any circumstances.
For customers who have homes near the ocean, Cliffside recommends choosing non-metal items such as marble or wood for your projects. Salt air acts as an abrasive, and quickly erodes the lacquer coating. If you absolutely need (or desire) metal hardware, Cliffside recommends solid stainless steel, or certain solid brass finishes such as Black, Polished Brass, or Polished Chrome. Note that, even in optimum indoor conditions, no Cliffside finish has a lifetime guarantee under any circumstances.
If you’re going to paint or re-stain your cabinets now would be a good time to do that. I’m a painted wood kind of gal, so these cabinets got painted, plus it’s a lot quicker and easier to paint them than to sand and re-stain. After the doors and frames have been painted it’s time to install the hinges and the glass. Since my upper, upper cabinets will rarely get used I secured the glass with silicone, if your glass cabinets will get daily use then you might want to use silicone and glazing points. I also put removable frosted film on my glass because after we added puck lights to the upper, uppers I realized how ugly the inside of the cabinets looked.

Often, the hardest part in updating your kitchen hardware is deciding what will look best in your kitchen. The installation can be a simple DIY that will likely take less than two hours. However, if your kitchen cabinet hardware requires more than just a few screws but rather new fittings on your cabinets or drawers, contact a pro to ensure all of your new hardware fits perfectly.
I can totally appreciate that.  You’ll notice that these cabinets are also flush with the cabinet frames, which makes the hinges a little less noticeable.  But sometimes, the hinge effect just isn’t quite as charming, and can be more distracting than anything.  A lot depends on what kind of cabinet overlay you’re dealing with and the aesthetic that you’re looking for in this sort of project. 
Consider proportion, balance, aesthetics and function when deciding upon the size of a knob or pull for your kitchen cabinetry. A large cabinet door or drawer needs a larger piece of hardware, or maybe two, for proper functionality, but a smaller size knob or pull is appropriate for a smaller door or drawer. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. However, more contemporary designs call for longer pulls that are at least two-thirds of the length of the drawer or cabinet door. 
I mentioned to my super-smart carpenter brother, Mike, that I was wanting to update my hinges but was afraid of ruining my doors in the process.  I watched a YouTube video of DIYer who tried to install hidden hinges, and I’ll be polite and just say that the outcome was not a good one. Thus my fear. The place I ordered my new cabinets from couldn’t order replacement doors, so this was a one-shot deal.
Are your cabinets in good condition but old, worn out and dated looking (kind of like me!)? With just a few tweaks you can bring them into this century and get another 10 to 15 years of life out of them. It seems like back in the 70s and 80s kitchen cabinets were built on site and built to last! That’s the case with the kitchen I’m currently dealing with, the entire kitchen was site built, they made one long face frame for an 8’ bank of cabinets – picture all the face frames of your cabinets connected together and installed as one piece, that’s how this kitchen is. Anyway, I was happy with the layout, it’s pretty basic, so to save some money I decided to work with the existing cabinets by removing the valance, replacing the exposed hinges with concealed hinges and adding glass inserts to the upper, upper cabinets – you’ll see what I mean in a minute. If you have ever thought of updating your dated kitchen cabinets, you’ll definitely want to check out this article in all its splendor.
Hi Diane….Glad to see you again and happy to see the progress on your lake home. I was a subscriber and then suddenly lost you about the time you started working on your staircase! I was afraid it had driven you away from your blog!! You showed up on another blog yesterday and now I plan to catch up on all I have missed. Thank you for accepting me again!!

Shake a can of spray paint for the full amount of time recommended by the manufacturer. Position the can the recommended distance from the hinges and the screws to spray a light coat of paint. Use steady side-to-side sweeping strokes and maintain a consistent distance from the hinges to ensure a uniform coat of paint. Shake the can frequently while you spray, and spray the sides and edges. Allow the paint to dry for the amount of time recommended by the manufacturer. Apply a second coat of paint and allow it to dry completely.


Cabinet hardware sizes can vary depending on your own personal design preferences, but you’ll want to choose a size that is both stylish and functional. Bar pull sizes are generally determined by the “center-to-center” measurement (the distance between the two screw holes). If you have pre-drilled cabinetry, you’ll need to buy hardware that fits the existing center-to-center measurement. Otherwise, you’re left to your own devices in choosing the size of your cabinet hardware. Here are a few general guidelines to follow:
Flat-panel cabinets.Most often seen in modern or contemporary kitchens, flat-panel cabinets embrace minimal embellishment to focus on natural materials. Subtle hardware choices are best, such as stainless steel bar pulls. You often see long, extended versions placed on the door or drawer.If you prefer square edges, you can choose a flat bar pull. Recessed pulls offer a functional option that work especially well for high-traffic kitchens. If you’re aiming for a minimalist look to your kitchen, you might consider discreet tab pulls for your flat-style cabinets.
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.
​If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go.  If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself.  If, however,  you decide on a warm metal faucets, door hinges or lighting fixtures,  many of us would have to hire a professional or handyman to replace those items.  But cabinet hardware can easily be switch out by almost anyone.  Just make sure you use standard sized hardware.
We also did that. Our handles are those stainless steel round bars. Loved the look with our white slab door/drawer fronts! Turned out there was big problem with sides of the horizontal drawer pulls snagging pants pockets. So, replaced those with centered flush type steel rectangular pulls that we mounted on the drawers after using router to make mortise holes No more snagging pockets!
Once you have decided on a style and shape for your hardware, you still need to choose the finish for your knobs and pulls. A shiny chrome finish has a modern feel, while brushed nickel or pewter may bring a more traditional look to your kitchen. Black hardware can be modern in a glossy finish or traditional with a matte finish. Many hardware lines come in several different finishes to help you find exactly the look you want.
Installing new hinges can be easy, but only when choosing the correct cabinet hinge upgrade. The door style, door thickness, and hinge type, all play a role. Once this information is obtained, you should be able to find a soft-close hinge that is a direct retrofit to the existing hinge, or choose one of the many independent dampers and keep your current hinges.
Hello Mr. TretheweyMy name is terry cotto, when we built our beautiful home 16 years ago, in Sierra Madre Ca I had my claw tub installed,( my child hood remembrance) It appears, that the claw legs of the tub were not installed properly, and one leg fell off , tub was slightly tipping to the right. I had a handyman come over and reinstall the claw legs, tighten so this would not happen again. The other day, while I was bathing I noticed the seal of the drain on the outside rubber was not laying properly, plus it was leaking, ( I think this was due to the leg falling off and unbalancing the ring. Well, now I really don't know what to do about that. I believe the thing to do is remove the cover off the top drain , ok, but than what do I have to move the claw tub, impossible. How do I replace the rubber of the outside of the top drain pipe, it appears to be brittle. (Not good)Please answer my questions, and I will hire the handy man again to help me. Thank you. I have learned so much from T.O.H weekly shows, I am a loyal fan at 75. I tell my 80 year old husband, you need to watch these shows with me, and we can do it ourselves, the right way. God Bless you all for the great job your doing, I need to know how to do it right, so it doesn't happen again. a picture would be good, I can see exactly how its done?
Before you get to hardware, it’s crucial to select your cabinet doors. The type of door you select will influence the style tremendously. The most popular styles of cabinet doors at the moment are Shaker, traditional, and modern. A Shaker-style cabinet front is a utilitarian design, with four rails and one middle, slightly recessed, center panel. It’s clean and simple design that can work well with most kitchen styles.
×