And starting to play with my new HVLP turbine spray system.  (Whenever I say HVLP turbine, I think of the movie “A Christmas Story” and how Ralphie describes his Red Ryder BB gun – “an official Red Ryder, carbine action, two-hundred shot range model air rifle.”  I think I’m equally enamored with my new gun, even if it doesn’t have a compass and a stock. 😉
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
Look to the other elements of your kitchen to help you determine the right style for your kitchen hardware. You’ll notice that your cabinets, countertop edges, and lighting fixtures have either square or curved lines. Choose hardware that matches those lines. Curved hardware tends to be more traditional, while square hardware styles are often more contemporary.

Kitchen knobs, pulls, and hinges have come a long way from the traditional styles that have been available over the years. No longer are homeowners limited to plain, simple, and functional. Instead, functional and pretty can now go hand in hand. Today’s styles include finishes in antique copper, iron, nickel, polished chrome, aged bronze, polished brass, glass, stainless steel, and antique brass. Additionally, a variety of knobs, handles, and pulls are available in ceramic styles.
Cabinet hardware sizes can vary depending on your own personal design preferences, but you’ll want to choose a size that is both stylish and functional. Bar pull sizes are generally determined by the “center-to-center” measurement (the distance between the two screw holes). If you have pre-drilled cabinetry, you’ll need to buy hardware that fits the existing center-to-center measurement. Otherwise, you’re left to your own devices in choosing the size of your cabinet hardware. Here are a few general guidelines to follow:
I have the exact hinge you mentioned under the caption “Then there are Overlay Hinges where you can see part of the hinge as well.” My problem is that on the 3 sets of doors we have that have no center stile, the doors are pushed too far toward center, therefore not enough space to close properly. Any suggestions other than taking down the doors and planing them? Hate that option on already completely finished doors. Great informative post.

When choosing a backsplash color scheme, keep in mind the type of look you want for your kitchen. By choosing a backsplash color that blends in with your wall color, you’ll be creating a streamlined, coordinated look. If you want to make a statement and have your backsplash pop, try choosing one or even a few colors that accent your wall color, making it stand out from the background.
At this point, you will have narrowed down your hardware choices to a specific style, type, size and finish. Next thing to incorporate is your budget. A good starting point is to count how many knobs and pulls you will need for your cabinetry and determine a price range that is comfortable for you. Many hardware manufacturers have multiple lines of varying quality and price, so be sure to find a manufacturer that uses high-quality materials. Buying cheap can seem like a good idea in the short run, but cheaper metals will degrade faster down the road and face a much higher risk of breaking or bending. Stainless steel hardware, for example, should be solid (not hollow) with a durable but even finish.

Then I drilled and drilled. If your drill is a wimpy one, be prepared for this to take a minute…or five.  I realized what a difference a decent drill makes during this process as I had three different ones going–one with a bit to drill the pilot holes, one with the hinge bit and one to use as a screw gun for screwing the screws into the cabinet doors. If you have lots of doors to do, it might be a good idea to borrow a second and/or third one from a friend or you’ll spend lots of time playing musical bits. If you have multiple drills, use the most powerful one for the large hinge-drilling bit.
Sandra, thank you so much for this awesome post! I’m remodeling my 40 yr old kitchen, and wanted to get rid of the visible old fashioned hinges that show! I had absolutely no clue as to what type of cabinets I have until I read your post! I completely understand now, and will be purchasing the “concealed surface mount overlay hinges for face frame cabinets” I know the 3 holes on the outside will be visible when I change out the hinges, so I’ll just fill them in with wood filler and sand before repainting. You’re so smart, informative and detail oriented just like me! Thank you again so much for this wonderful lesson on cabinets and hinges! I’m subscribing to your website or blog or whatever you have!
​If you want to use warm metal like matte brass or gold or copper in your house, but are hesitant because you’re afraid it might go out of style in the next few years, adding warm metal cabinet hardware is a great way to go.  If brass, gold and copper do go out of style in the next few years, most cabinet hardware is pretty simple to replace all by yourself.  If, however,  you decide on a warm metal faucets, door hinges or lighting fixtures,  many of us would have to hire a professional or handyman to replace those items.  But cabinet hardware can easily be switch out by almost anyone.  Just make sure you use standard sized hardware.
For knobs on a cabinet with a stile, like Shaker-style cabinets, allow the stile to be a guide for hanging the knob. If the knob is too large to comfortably fit in the corner where the two stiles meet, then hang the knob centered on the vertical stile, with the bottom edge of the knob aligned with the top of the intersecting horizontal stile. (Or the top of the knob aligned with the bottom of the stile, for lower cabinets). The knobs in this kitchen from Ivory Lane are a good example.
Thanks so much. Isn’t it crazy how expensive hardware can be. Concealed hinges generally have the advantage of more adjustability. That is more important with inset doors and overlay doors that meet in the center of the cabinet with no center style. If you have a simple 1/2″ overlay and a center style, they are so forgiving and don’t require precise fiddle factor installation! LOL There’s no need for the more expensive hinges.

The timeless classics of solid brass styles, futuristic euro-design aluminum pieces, stunning granite and stainless steel combinations, and novelty handcrafted hardware can all be purchased for a fraction of the cost of replacing your entire set of kitchen cabinets. Give your kitchen a new look with the simple replacement of cabinet hardware. Sprucing up the kitchen has never been easier.
I'm shocked on how little power they want in the kitchen. One outlet on the island? Wait until the kids want to plug a phone or lap top in or they are stinging an extension cord across it to use a blender on the other end. The Refridge/stove/freezer wall sounds a bit scary also. Stove next to a fridge is almost always a no no. You need countertop on both sides of the stove, period.
Decide whether to install door catches. These will secure your doors while they are closed. Magnetic door catches are most often used. When your door closes, a small metal plate on the back of the door attaches itself to a magnet on the cabinet frame. You will hear a slight clicking sound as they make contact. Two additional styles that provide a smooth operation are spring-roller catches and friction catches. These catches are silent when they latch.
Handles are sold by the center to center measurement(1). Center to center can be spelled out or the universally known “C/C” could be used. Knobs are sold by the diameter(4) of the knob.The measurement could be in inches or millimeters (MM) CabinetParts has both measurements listed for your convenience. (Tip: to convert millimeters to inches use this formula: MM ÷ 25.4)Here is a diagram showing how these are measured:The overall length(2) and the projection(3) are offered when they are available from the manufacturer.Choosing a finish is going to be entirely up to you. Maybe your cabinets need a satin nickel look for a more modern look or maybe you are in the mood for flat black finished hardware for a more southwestern feel, or maybe weathered copper is your fancy. There are many, many choices for finish to make your kitchen look like a million bucks.The type of handle or knob will depend on what you like or maybe the motif of the rest of the room or house. There are modern, eclectic, or traditional looks and more.Most collections will have a pull and a knob that “match” so you can have the same finish throughout the room. You do not always have to choose pieces from the same collection, just remember to always choose the finish from the same manufacturer. Even though different manufacturers may have finishes that have the same name, they will often vary in the color and shade.These choices will be among the most important of the entire project. A knob and pull will put the finishing touch on the project and be one of the first things people will notice.Sometimes the hardware is noticed before the color or type of cabinet or door.Here is a listing of all of the manufacturers CabinetParts.com offers: Top Konbs, Amerock, Schaub and Co, Atlas Homewares, Notting Hill, Berenson, Jeffrey Alexander, Century Hardware, Hickory Hardware, Laurey Hardware, Liberty Hardware, Elements, Stone Mill Hardware, Hafele, R. Christensen, MNG Hardware, Acorn Mfg.Some of the companies listed above also offer Bath Hardware and Decorative Home Accents that may help complete a project.
Cup pulls add a unique style to drawers by going beyond the basic drawer handle. Whether you’re looking for a way to add antique or rustic style to your kitchen or you want to add modern flair, cup pulls enhance any décor. Since cabinet pulls are used frequently each day, look for quality metal styles that are durable and built to last. Cup pulls also come in interesting shapes and designs like leaves and clamshells to give your kitchen a fun aesthetic.
3. Traditionally, your hardware should be the same finish as your kitchen sink faucet. However, mixing and matching metals is on trend in contemporary and transitional homes. Don’t forget to consider your appliances and light fixtures as well. Black appliances look lovely beside bronze or black hardware, while stainless steel and nickel play nicely together. 
The size of your cabinets will influence the size of your knobs. If your cabinets are smaller in scale you’ll want to opt for hardware that is likewise, such as minimal-scale circular knobs. Longer hardware is necessary when you have extra long cabinet doors—or can be used if you want to make a more of dramatic statement. Most cabinet doors are 24”, so you want a knob about 2”-3” size knob. For a larger cabinet door you can size up to 3½” or 4”. For a cabinet door under 20”, source hardware that’s closer to 1” to 2” size in diameter or length.
×